Maxima Forums - Search Results

 
Search: Posts Made By: akurtzer57
Showing results 1 to 25 of 494
Search took 0.17 seconds.
04-22-2017, 06:58 AM
Replies: 8
Views: 545
Posted By akurtzer57

Yes I've ran a setup like this and had it built...

Yes I've ran a setup like this and had it built in a night. If so a engine swap you still have do all that then switch bunch **** over on motor. Motors are basically identical. Internally.
04-20-2017, 04:39 PM
Replies: 8
Views: 545
Posted By akurtzer57

The vg30e blocks are all the same. You can't just...

The vg30e blocks are all the same. You can't just drop Z31 motor in. Oil pans are different intakes will work with mods. Fuel rails need some work. To my knowledge I'm the only one ever run the Z31...
02-12-2017, 08:27 AM
Replies: 379
Views: 27,056
Posted By akurtzer57

I shortened my water pipe and changed it quite a...

I shortened my water pipe and changed it quite a bit also gave me alot more room. Of course my manifolds somewhat in the way.
02-09-2017, 11:57 AM
Replies: 15
Views: 1,882
Posted By akurtzer57

Awesome. I need get going on my maxiam and stop...

Awesome. I need get going on my maxiam and stop doing side work.
01-07-2017, 02:55 PM
Replies: 12
Views: 604
Posted By akurtzer57

Dyno my car and break records.

Dyno my car and break records.
12-18-2016, 02:26 PM
Replies: 4
Views: 545
Posted By akurtzer57

When people say autotragic meaning there junk. Do...

When people say autotragic meaning there junk. Do a 5 speed swap.
12-18-2016, 02:08 PM
Replies: 13
Views: 1,961
Posted By akurtzer57

Went back and looked at some z31 alot them making...

Went back and looked at some z31 alot them making 260 and mid 300s torque with t3. But ya 11.8 afr I wouldn't push it any more than already is.
12-17-2016, 04:24 PM
Replies: 13
Views: 1,961
Posted By akurtzer57

Right where I would expect it to be get that...

Right where I would expect it to be get that cranked up to 12-14 with a controller and you will easily see 350hp and high 300s torque.
11-27-2016, 07:45 AM
Replies: 15
Views: 1,882
Posted By akurtzer57

I can edit your bin and email it to you then just...

I can edit your bin and email it to you then just you can use flash n burn software to burn the eprom. I never could find any software to read them right why I used nistune to edit them.
11-26-2016, 06:48 AM
Replies: 15
Views: 1,882
Posted By akurtzer57

yes it is. I need order another socket to switch...

yes it is. I need order another socket to switch my nistune over. If doing eprom get you a zif socket 20x easier pulling eprom to burn it.
10-30-2016, 06:37 PM
Replies: 4
Views: 546
Posted By akurtzer57

Yes a replacement maf direct bolt on. If you have...

Yes a replacement maf direct bolt on. If you have a code thrown you may have to do reset on the ecm just unhook the battery for few min.
10-25-2016, 04:35 PM
Replies: 5
Views: 4,411
Posted By akurtzer57

9.1 NA motor stock z31 fuel system run 14psi...

9.1 NA motor stock z31 fuel system run 14psi break 13s easy.
10-23-2016, 04:59 PM
Replies: 5
Views: 4,411
Posted By akurtzer57

If wouldnt be suprised if you broke 13s with a...

If wouldnt be suprised if you broke 13s with a good 60 ft. Your a NA motor or no?
10-23-2016, 04:31 PM
Replies: 379
Views: 27,056
Posted By akurtzer57

I can crawl under my car and give you some...

I can crawl under my car and give you some measurements tomorrow afternoon.
10-16-2016, 07:18 PM
Replies: 5
Views: 758
Posted By akurtzer57

Change out the CHTS vg famous for having issues...

Change out the CHTS vg famous for having issues with it go bad. Causing all kinds rich lean condistions which also affect your idle.
10-07-2016, 04:02 PM
Replies: 5
Views: 4,411
Posted By akurtzer57

Ill be running mine this spring I got rough idea...

Ill be running mine this spring I got rough idea what it should run.
09-26-2016, 08:16 PM
Replies: 6
Views: 593
Posted By akurtzer57

VE30DE VG30E Alternator K050323 ...

VE30DE VG30E
Alternator K050323 K040292
Air Conditionin K040460 K040460
Power Steering K040378 K040395
06-09-2016, 05:14 PM
Replies: 15
Views: 1,882
Posted By akurtzer57

I don't see the 88 maxima ecu listed on Nistune...

I don't see the 88 maxima ecu listed on Nistune may not be supported. I would stick with the z31 ecu if it was me. Here is a screenshot of a j30 maxima stock timing map and then a z31 turbo timing...
06-08-2016, 07:26 PM
Replies: 15
Views: 1,882
Posted By akurtzer57

I do have a z31 bin file with anti lag....

I do have a z31 bin file with anti lag....
06-08-2016, 07:26 PM
Replies: 15
Views: 1,882
Posted By akurtzer57

Id go to moates.net have had good luck with there...

Id go to moates.net have had good luck with there burners. Ill gladly write you a bin file on nistune I can send you any bin you want I have all z31 and maxima bins. Should be able just write tune...
06-08-2016, 06:54 PM
Replies: 15
Views: 1,882
Posted By akurtzer57

Ive done quite a bit of it with hondas. Ive aslo...

Ive done quite a bit of it with hondas. Ive aslo wrote tunes with nistune and burned eproms for people
06-05-2016, 08:33 PM
Replies: 159
Views: 167,854
Posted By akurtzer57

Yes you can run high impedance injectors on a low...

Yes you can run high impedance injectors on a low impedance ecu people do it I personally would never do it. When you get ready do 370cc Ill sell you my set dirt cheap in 3rd gen rail. There type 1...
06-05-2016, 03:32 PM
Replies: 159
Views: 167,854
Posted By akurtzer57

84-86 ecus are low imedance the 88 ecu is a high...

84-86 ecus are low imedance the 88 ecu is a high impedance. What impedance injectors you have?
05-29-2016, 06:47 PM
Replies: 6
Views: 933
Posted By akurtzer57

Was pretty much direct swap. I believe I had to...

Was pretty much direct swap. I believe I had to just slightly enlarge the alignment pin. Wouldn't quite slip on my flywheel with paint etc. Did use the maxima throw out bearing.
05-29-2016, 06:45 PM
Replies: 5
Views: 1,264
Posted By akurtzer57

Looks like you need use a z31 ecu. It can be any...

Looks like you need use a z31 ecu. It can be any z31 ecu just be sure to match the injector drivers to you impedance ecu. z31 had high and low impedance. I would recommend using a 87+ turbo ecu...
Showing results 1 to 25 of 494
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.