FS: VQ Turbo Manifolds and Turbo from VQ30DET
#1
Supporting Maxima.org Member
Thread Starter
iTrader: (15)
Join Date: Oct 2004
Location: my garage
Posts: 2,220
FS: VQ Turbo Manifolds and Turbo from VQ30DET
I bought a VQ30DET for my 240SX and I'm selling the exhaust manifolds and T-3 turbo that came with it. This turbo will produce around 300 whp. These manifolds will fit on any Maxima VQ. I'm asking $200 plus shipping OBO.
The turbo has a very small amount of shaft play, other than that it appears to be in working condition. The o2 sensor and cartridge fittings are not included.
The turbo has a very small amount of shaft play, other than that it appears to be in working condition. The o2 sensor and cartridge fittings are not included.
Last edited by 505max94se; 03-31-2008 at 09:31 AM.
#2
I bought a VQ30DET for my 240SX and I'm selling the exhaust manifolds and T-3 turbo that came with it. This turbo will produce around 300 whp. These manifolds will fit on any Maxima VQ. I'm asking $350 plus shipping OBO.
The turbo has a very small amount of shaft play, other than that it appears to be in working condition. The o2 sensor and cartridge fittings are not included.
The turbo has a very small amount of shaft play, other than that it appears to be in working condition. The o2 sensor and cartridge fittings are not included.
#3
Supporting Maxima.org Member
Thread Starter
iTrader: (15)
Join Date: Oct 2004
Location: my garage
Posts: 2,220
i understand that these manifold will fit the vq 30 but will they properly position the turbo to clear the FWD tranny and other goodies, basically my question is would this be a direct bolt on to my 5th gen 3 liter or would i have to modify something to get them to fit right?
#6
Doh, I just saw this now
Just a note, the crossover pipe will hit the starter on a FWD VQ. You will have to custom a new crossover pipe to run this with a FWD setup. I saw this too late. I would have scooped this up for sure. If there's another set of VQ30DET manis laying around somewhere out there...I'd be glad to take it off your hands.
Just a note, the crossover pipe will hit the starter on a FWD VQ. You will have to custom a new crossover pipe to run this with a FWD setup. I saw this too late. I would have scooped this up for sure. If there's another set of VQ30DET manis laying around somewhere out there...I'd be glad to take it off your hands.
#7
Supporting Maxima.org Member
Thread Starter
iTrader: (15)
Join Date: Oct 2004
Location: my garage
Posts: 2,220
Doh, I just saw this now
Just a note, the crossover pipe will hit the starter on a FWD VQ. You will have to custom a new crossover pipe to run this with a FWD setup. I saw this too late. I would have scooped this up for sure. If there's another set of VQ30DET manis laying around somewhere out there...I'd be glad to take it off your hands.
Just a note, the crossover pipe will hit the starter on a FWD VQ. You will have to custom a new crossover pipe to run this with a FWD setup. I saw this too late. I would have scooped this up for sure. If there's another set of VQ30DET manis laying around somewhere out there...I'd be glad to take it off your hands.
Anyways, my friend has another set with the turbo. I'm not sure about the condition of the turbo, but you should shoot me a pm if you're interested.
#8
I was following up on the engine on other threads and the RWD starter is on the other side of the block. The FWD starter is just above the bellhousing which is where the crossover pipe runs. I could be mistaken though. I haven't personally done the swap yet. Just what I've read in other forums.
PM sent.
PM sent.
Last edited by bohead; 04-16-2008 at 08:06 PM.
Thread
Thread Starter
Forum
Replies
Last Post
litch
4th Generation Maxima (1995-1999)
123
01-04-2024 07:01 PM