3rd gen complete part out
#1
3rd gen complete part out
all parts are from a 93 se and 90 se
ignition coils for ve all sold
have 3 window regulators and motors both drivers side and rear passenger. 25 shipped
ve fuel rails and injectors sold
ve gauge cluster sold
have 5th gen wheels for sale 530 shipped http://forums.maxima.org/showthread.php?t=543771
black interior
2 sets of good headlights
good taillights
2 rear garnishes red/black
good grills with emblems
have original 93 se wheels
trunk switch
new alternator
new fuel pump
new power steering pump
new knock sensor and harness
engine parts can be taken off too.
located in sc
shoot prices
ignition coils for ve all sold
have 3 window regulators and motors both drivers side and rear passenger. 25 shipped
ve fuel rails and injectors sold
ve gauge cluster sold
have 5th gen wheels for sale 530 shipped http://forums.maxima.org/showthread.php?t=543771
black interior
2 sets of good headlights
good taillights
2 rear garnishes red/black
good grills with emblems
have original 93 se wheels
trunk switch
new alternator
new fuel pump
new power steering pump
new knock sensor and harness
engine parts can be taken off too.
located in sc
shoot prices
Last edited by mooze; 11-12-2007 at 01:25 PM.
#15
Do you have the engine ECU still? If so, do you mind opening up the case(should be four screws) and taking a few photos of the inside of it? If it has what I am looking for, then I will buy it for sure
US$80 + shipping to Australia enough?
US$80 + shipping to Australia enough?
#16
oad sensing assy-valves (brake part)
Is there any way you could remove the load sensing assy-valves? (part # 46400 in the diagram) I imagine it would be somewhat corroded and prone to being damaged upon removal but what do you think?
You will only have this part if you had abs brakes
http://www.courtesyparts.com/betasit...1706_1711.html
located at the rear of the car.
It would mean the Maxima world to me.
Thank you
You will only have this part if you had abs brakes
http://www.courtesyparts.com/betasit...1706_1711.html
located at the rear of the car.
It would mean the Maxima world to me.
Thank you
#17
#19
#20
Is there any way you could remove the load sensing assy-valves? (part # 46400 in the diagram) I imagine it would be somewhat corroded and prone to being damaged upon removal but what do you think?
You will only have this part if you had abs brakes
http://www.courtesyparts.com/betasit...1706_1711.html
located at the rear of the car.
It would mean the Maxima world to me.
Thank you
You will only have this part if you had abs brakes
http://www.courtesyparts.com/betasit...1706_1711.html
located at the rear of the car.
It would mean the Maxima world to me.
Thank you
#21
Is there any way you could remove the load sensing assy-valves? (part # 46400 in the diagram) I imagine it would be somewhat corroded and prone to being damaged upon removal but what do you think?
You will only have this part if you had abs brakes
http://www.courtesyparts.com/betasit...1706_1711.html
located at the rear of the car.
It would mean the Maxima world to me.
Thank you
You will only have this part if you had abs brakes
http://www.courtesyparts.com/betasit...1706_1711.html
located at the rear of the car.
It would mean the Maxima world to me.
Thank you
#22
how much for all 4 strut assys (rears with brakes still attached.. fronts you can take/leave either way doesn't matter), both swaybars, and the handbrake cable and assoc. hardware?
as well as the PS pump.
also is this VE car ABS or non?
as well as the PS pump.
also is this VE car ABS or non?
Last edited by CapedCadaver; 11-21-2007 at 09:18 PM.
#31
Thread
Thread Starter
Forum
Replies
Last Post
Team STILLEN
Autocrossing and Road Course Racing
0
08-10-2015 04:29 PM
ViciousVQ30
4th Generation Classifieds (1995-1999)
0
08-05-2015 05:40 PM