Maxima Forums

Maxima Forums (https://maxima.org/forums/)
-   4th Generation Maxima (1995-1999) (https://maxima.org/forums/4th-generation-maxima-1995-1999-6/)
-   -   Replacing Fuel injectors, how do i prep? (https://maxima.org/forums/4th-generation-maxima-1995-1999/397999-replacing-fuel-injectors-how-do-i-prep.html)

CaptainFill 06-09-2007 08:54 PM

Replacing Fuel injectors, how do i prep?
 
Hello,

I am replacing one stock fuel injector and the last time I did it I managed to mess something up because i didnt drain the gas from the line beforehand.

Now that I am doing it again I would like to approach it a little smarter and drain the line first.

So what im really asking is what do i need to prep for a fuel injector change?

Thanks!

mynameispee 06-09-2007 09:02 PM

pull the fuel pump replay and turn the car on until it dies then you should be fine.

95BLKMAX 06-10-2007 10:01 AM

be sure to coat the new injector's o-rings with new engine oil. Makes for a much better seal and this is what it says to do on the FSM if you dont trust me, lol.

When reinstalling the fuel rail, be sure not to crush any of the injector grommets, otherwise, vaccum leak FTL.

Goold luck

Why are you replacing ONE injector anyways??

CaptainFill 06-10-2007 11:53 AM

Thaanks. One of my injectors is clogged and I cant afford 6 new injectors.

CaptainFill 06-10-2007 12:37 PM

Well I replaced my injector and its like a have a brand new car.

It fixed....

Rough shifting
Slow acceleration
Rattling in idle and stopped
Misfiring
Hesitation from accelerating around 1.5k
Heavy downshifting

I cant be happier and it only took 15 minutes.

95BLKMAX 06-10-2007 01:04 PM

tight work man. I bet you're happy. What mods do you have???

CaptainFill 06-10-2007 01:15 PM

No mods, just a stock 95' GLE. Id like to do stuff to it but it has fairly high miles and any mods to it might put more strain on the engine and tranny. Id like to do a 3.5 swap w/ tranny, but i dont have the money for that now.

95BLKMAX 06-10-2007 02:13 PM

DEKs run for ~$400-$600. plus, any mods u do now, like ypipe and intake, can be used on the new motor, 3.5 included :-D. But yea man, take ur time with it and have fun

AlphaDog 01-24-2009 12:29 PM

Just wanted to say thanks to the posters in this thread. I replaced an injector today in my '95 from the info here.

Awesome work guys! :)

BogardiDough 02-02-2009 06:10 PM

just curious, how much did each injector cost you?

trooplewis 02-02-2009 06:30 PM


Originally Posted by BogardiDough (Post 6849331)
just curious, how much did each injector cost you?

And also how did you know you had a bad injector?

pmohr 02-02-2009 06:36 PM


Originally Posted by trooplewis (Post 6849401)
And also how did you know you had a bad injector?

You ohm out the injector, if it tests bad you replace it. Typically you do so after failing to find a coil or plug as the fault of a misfire. Injector is the next step

I can get injectors locally for $8 or $100, it depends on where you get them.

aznprid972 02-02-2009 10:12 PM

http://www.vqpower.com/v2/articles.php?article_id=153


All times are GMT -7. The time now is 07:31 PM.


© 2024 MH Sub I, LLC dba Internet Brands