I just finished cleaning my K&N filter and I added PVC piping instead of the ridged drainage piping I had in there. Last step will be adding the elbow PVC piece and cutting a hole for some hot ram air action.

Also I notice my scoop and airbox weren't 100% connected. They are now.

 

Then U'll be like MeEeEeEeEeEeEe!

 

Got any pics?

 

hehe....I think mine is still in beta version Once i get some free time, I will upgrade...

 

YJ chants *Custom CAI* *Custom CAI*

 

you got details? or is it a secret

 

YEAH!!!

 

Nope.
Just buy the tubing from JCwhitney for about 60 bucks.
Modify it to fit the JWT pop charger or a smaller filter if ya like
Be sure to drill

 

Or if you're ghetto, rig a shop vac through the hole.

Would anyone want to try?

 

hehe...thats what my OSCAI consists of

 

Really? You actually drilled a hole in the metal and routed the shop vac through?

 

no.... I think I misunderstood..... I have shop vac tubing going down through a hole in the splash guard for my OSCAI setup. fear SHOPVAC TUBING!

 

Blah! I meant shop vac tubing through the CAI hole.

 

yes, I realize that now....my bad....sorry

 

Hehehe Don't be sorry. Wanna try the other way?

 

hmmm... got to get a pop-charger then and tear it all up.....maybe one of those generic cone filter housings will also work..... but right now, I am set on getting a Y-pipe..... I will try and get one really soon.

 

I can't seem to view the pics of your OSCAI from the path in your sig.
I found the thread, but the pic is invisible.
Can you post them here again?
Thanks

 

Here ya go!

 

I have 3 generic Top speed intakes for sale for 30 bucks each UMD

 

How did you take out the air inlet out. That one thing that hooks up the air box. I tried to take it out put did not want to break anything so I left it alone.

 

hehe...cool....but I think I will stick with the OSCAI I hve right now....If I have some time to mess around, then I may try something like what you have

 

Gently ... Just Work it around ... Left and Right ... In and Out ... and It will Come!

 

I tried that and It didn't come.

 

Check this out

http://dodgegarage.www2.50megs.com/c...ercooling.html

Now this is homebrew. This guy is in the 12's. I guarantee this homebrew duct work yields more than 5 HP.

 

Jesus... that is one OOGLIE job he did. If my engine compartment looked like that I'd kill myself.

Maxima
Horsepower 222
Cylinders 6
Feet of duct tape under hood 0

 

I noticed that my JWT intake wasn't connected 100% either. Thanks a bunch! haha just playing. I did get Chad's bike hooked up with some RAM air though. It sounds nuts! Too bad he's selling it. Oh and I got your emails and yeah give me a call on the next install!

 

I should be getting a Y-pipe within the next few months. Or I might be doing some stereo stuff. You up for it?

 

I can forgive that. He's just trying out a new intercooler setup. This minivan runs 12's and his Reliant K car runs 10's. This guy is a genius.

 

Damn, that dude is breakin out the dryer ducts!!! HARDCORE OSCAI!!!!!

 

can anyone tell me how to pull out the sensors on the air intake. no matter how hard i pull i can not pull them out. this makes it nearly impossible to install my oscai.

 

the sensor that is actually stuck into the tubing can be a little tough, but you just have to pull it straight out. If you pull straight out, it should be just fine. That is the only way to get it out. The other one is bolted to the front of the scoop, so all you have to do is remove the bolt.