FL VQ35DE Ultimate NA Part Out, Built Small Block, Jenvey Individual Throttle Bodies etc
#1
VQ35DE Ultimate NA Part Out, Built Small Block, Jenvey Individual Throttle Bodies etc
Where to begin, the time has come, I'm in college, and am no longer willing to invest into my project anymore. Time to part out to pay for school.
315NA WHP video.
Was a 2003 VQ Block.
Engine :
Short Block
New 11.1 96MM Wiseco Pistons
New Eagle Rods
New ARP Rod Bolts
Engine Bore/Hone/Balancing and machine work for HR Headgasket compatibility made at South Florida Crank in Lake Worth.
New ARP Mains + Revvup Oil Pump
New ACL Main/Rod Race Bearings Installed
Here is a link to the coolant upgrade for the HR Headgasket to be used.
http://www.jimwolftechnology.com/wol...HEAD_BOLTS.pdf
I paid about 3800$ for the parts machine work and block, the machine work is quality work and I have videos of the car dyno at 300WHP NA and 320WHP NA with no problems. I've only placed around 400 miles on the car because I've always had a daily. Right now got my 92' Corolla. Anyway, price is $2800 for an NA built bottom end.
Heads: Selling the L19 Headstuds as shown above, for 350$ shipped.
Engine :
320CFM Port and Polished Head, JWT Valvesprings. Again made 300whp. Valve springs. Flowbenched and made 320CFM. JWT C9 Camshaft. SOLD HEADS
Intake :
Jenvey Individual Throttle Body
Cost around 3000$ Selling for $2350, taking a big loss on this setup but with them I made 320whp NA. SOLD
Engine Management:
Pro48 ECU + Harness and Adaptor. $1600 Shipped.
Fuel Management :
E85 Setup with Fuel Surge Tank
Have the ethanol gauge and everything.
My name is Kevin and I will post videos and pictures. Contact is 954-479-7478 and e-mail is kgkeen101@gmail.com I am located in Orlando 32817. I have not included shipping with the costs because I know the heads and block are big so I'd like to get a quote before I find out I'm overspending on shipping and taking a loss. Hope that sounds reasonable.
Was a 2003 VQ Block.
Engine :
Short Block
New 11.1 96MM Wiseco Pistons
New Eagle Rods
New ARP Rod Bolts
Engine Bore/Hone/Balancing and machine work for HR Headgasket compatibility made at South Florida Crank in Lake Worth.
New ARP Mains + Revvup Oil Pump
New ACL Main/Rod Race Bearings Installed
Here is a link to the coolant upgrade for the HR Headgasket to be used.
http://www.jimwolftechnology.com/wol...HEAD_BOLTS.pdf
I paid about 3800$ for the parts machine work and block, the machine work is quality work and I have videos of the car dyno at 300WHP NA and 320WHP NA with no problems. I've only placed around 400 miles on the car because I've always had a daily. Right now got my 92' Corolla. Anyway, price is $2800 for an NA built bottom end.
Heads: Selling the L19 Headstuds as shown above, for 350$ shipped.
Engine :
320CFM Port and Polished Head, JWT Valvesprings. Again made 300whp. Valve springs. Flowbenched and made 320CFM. JWT C9 Camshaft. SOLD HEADS
Intake :
Jenvey Individual Throttle Body
Cost around 3000$ Selling for $2350, taking a big loss on this setup but with them I made 320whp NA. SOLD
Engine Management:
Pro48 ECU + Harness and Adaptor. $1600 Shipped.
Fuel Management :
E85 Setup with Fuel Surge Tank
Have the ethanol gauge and everything.
My name is Kevin and I will post videos and pictures. Contact is 954-479-7478 and e-mail is kgkeen101@gmail.com I am located in Orlando 32817. I have not included shipping with the costs because I know the heads and block are big so I'd like to get a quote before I find out I'm overspending on shipping and taking a loss. Hope that sounds reasonable.
Last edited by Kgkeen101; 09-19-2012 at 11:26 AM.
Thread
Thread Starter
Forum
Replies
Last Post
vingodine
5th Generation Classifieds (2000-2003)
45
05-21-2016 12:46 PM
homewrecker
5th Generation Maxima (2000-2003)
13
08-24-2015 08:56 PM
kirkhilles
5th Generation Maxima (2000-2003)
2
08-08-2015 10:53 AM