Phone Mount for 8th Gen
 

I recently dumped XM after about 8 years and just use Pandora in my Altima. I bought this and it works tremendously.

Toaster, I suggest checking out ProClip. Following link is for the mount. Note you'll also need to buy the device holder for your specific phone from them, which you'll find on this site. I've had in my 2005 Maxima for many years, love it.

https://www.proclipusa.com/product/8...-console-mount

https://cimg4.ibsrv.net/gimg/maxima....6b9825b188.jpg

I use this one in all my cars. In the Max is clamps solidly into the front right-hand vent over the GPS. Sturdy, does not slip over rough roads, and about $5 bucks in-store Walmart, and is identical to what you'll find on-line here for a couple of $$ more:

https://www.walmart.com/ip/WizGear-U...ne-6/147742509

Those were on slick deals this AM..2 for 4 bucks...I missed out..little late..was going to get them for my other cars... :(

The CD slot mounts are great, in my opinion.

perfectly stable. i had my ipad mounted there since 2016 never fell. i mounted my phone on the drivers side air-vent

Toaster, no, I have never found where ProClip mounts to be too low. I understand how some might prefer their phone higher. But the trade-off is then you're blocking something. The benefit of the ProClip is not only is it more sturdy than most phone holders and seamlessly fits into the interior better than most, but you're not blocking anything whatsoever.

I worry that the vent clips would break the vent louvers, would make for a very expensive phone mount!

That crossed my mind when I was looking. The one I bought is pretty padded where it grabs the louvers....Not worried about it breaking anymore.

I don't believe that poses a problem at all. They way the mount clip fits in between 3 louvers makes for a solid surface. It grabs a center louver, and is kinda locked in there by pressure from the louvers above and below, although not enough to bend the louvers. Also, where I mount it, the base of the vent mount rides the left side of the louver frame, adding additional support. No way that is a weak mounting. It is plenty strong to keep my rather large and heavy Android firmly in place. I mounted the included thin metal "magnet plate" towards the bottom of my phone (between the protective cover and the phone itself) so I can mount the phone rather high away from GPS/radio screen. Works very well for me.

Here's the mount I use in my maxima. I typically dont like vent mounts, but this works really well with the maxima. Chord doesn't block the screen either if it's plugged in. Got it on Amazon. Dont have the link,, but it's made by Torras
https://cimg6.ibsrv.net/gimg/maxima....2cc5d4f141.jpg

With the little hinged door open, my phone fits snugly between the door and the right temp adjustment knob, in landscape mode.

https://cimg7.ibsrv.net/gimg/maxima....b4cddd08d1.jpg

Hey sschumer, thanks for the ProClip info, just got mine and installed it.... It's perfect!

The only phone mount that I'll use is the Scosche Magic Mount. is a link to the vent one that I use. It mounts perfectly into the vent in my 2018 Maxima and the phone site on the lip below it vertically. If you don't like the vent one then you can order one that sticks to the dash. These are the best looking ones imo. They aren't bulky. They don't stick out a bunch.

Has anyone bought the Weathertech cup based phone mount. It looks pretty good and I would prefer that over a vent mount.

I use this
coupled with this

Yeah until you make a quick sharp left turn and it ends up in the passenger floor board, been there done that :laugh:

That sure won't happen with the ProClip, highlighted above.