looking for seat replacement
#1
looking for seat replacement
I have a 99 SE with tan, heated, power, leather seats. I love the seats but there isn't a lot support for lateral. Does anyone know of another seat from a nissan or other manufacture that would offer the same as what I have now but with better support. (I love to corner but hate the feeling of sliding in my seat.)
Maybe the newer models have better lateral control or how about the 350z or an older 240?
Has anyone ever done this already. I looked at Corbeau seats but they don't offer tan leather.
Thanks!
Tom
Maybe the newer models have better lateral control or how about the 350z or an older 240?
Has anyone ever done this already. I looked at Corbeau seats but they don't offer tan leather.
Thanks!
Tom
#5
#6
thanks. That's actaully what I was looking for.
Sweet looking.
One question though. Did it feel like you were sitting higher or lower than stock. I am tall and have to make sure I don't sit any higher than I already do.
Thanks again.
Sweet looking.
One question though. Did it feel like you were sitting higher or lower than stock. I am tall and have to make sure I don't sit any higher than I already do.
Thanks again.
#7
Slightly lower. Keep in mind what I did: Maxima base/rails/seatpan with 350Z bottom cushion/seatback. The 350Z bottom cushion is a lot thinner. So much so that I had to raise the seatpan up in the front with bolts and washers (spacers) to get the correct seat angle. You can do that or you could use extra padding between the seatpan and cushion in the mid-thigh area. You could do this with 350Z seat parts or any other seats that you like if you take the initiative to figure it out.
#8
Originally Posted by bhmax
Slightly lower. Keep in mind what I did: Maxima base/rails/seatpan with 350Z bottom cushion/seatback. The 350Z bottom cushion is a lot thinner. So much so that I had to raise the seatpan up in the front with bolts and washers (spacers) to get the correct seat angle. You can do that or you could use extra padding between the seatpan and cushion in the mid-thigh area. You could do this with 350Z seat parts or any other seats that you like if you take the initiative to figure it out.
so, did you just drill into the seat cushion to match the maxima rails, or did you drill holes in the rails to match the seat???
#9
Originally Posted by FLAVOR247
so, did you just drill into the seat cushion to match the maxima rails, or did you drill holes in the rails to match the seat???
#10
So this is it? This has to be one of the most lacking in Maximas. Corbeaus and 350Z seats are the only conversions that have been done? Would any of those ebay racing seats fit? Some even say they're for Maximas but don't go into detail about mounting? Anyone?
#11
Originally Posted by Midknight MAXX
So this is it? This has to be one of the most lacking in Maximas. Corbeaus and 350Z seats are the only conversions that have been done? Would any of those ebay racing seats fit? Some even say they're for Maximas but don't go into detail about mounting? Anyone?
The ones on ebay claim they will fit maxima's using their sliders but some modifications may be needed.
Ive emailed numerous sellers.
#12
Originally Posted by FLAVOR247
You can buy the Corbeaus sliders and use them for other seats, some may require alterign them a bit.
The ones on ebay claim they will fit maxima's using their sliders but some modifications may be needed.
Ive emailed numerous sellers.
The ones on ebay claim they will fit maxima's using their sliders but some modifications may be needed.
Ive emailed numerous sellers.
Thanks for the info. What altering exactly would have to be done?
Thread
Thread Starter
Forum
Replies
Last Post
vingodine
5th Generation Classifieds (2000-2003)
45
05-21-2016 12:46 PM