Supercharger $3200 Sold
• fits 95-01 Maxima
• Stillen supercharger kit
• Vortec v2-sc supercharger 3.125” pulley
• Greddy front mount intercooler (30 X 12 X 4) (W X H X D) not including end caps
• 3” custom charge pipe painted body color
• K&N air filter 3.5” diameter x 9” tall
• Custom cold air intake
• Greddy blow off valve
• Dual stage water/alcohol injection
• Custome SS water tank

Supercharger basic kit $2500 Sold, gone with complete setup above
• Basic Kit with 3.6 pulley
• Greddy blow off valve
• fits 95-01 Maxima

eManage (blue) $250 Sold
• data log harness (usually $130)
• boost switch (usually $200)

Gauge pod (replaces factory closck in 5th & 5.5 gens) $100 Sold

Gauge pod (replaces factory clock in 5th & 5.5 gens) $350 Sold, gone with complete setup above
• includes Greddy guages
• Greddy mechanical boost gauge
• Greddy electronic fuel pressure gauge
• Greddy electronic egt gauge

Custom hood with exchange $300
• trade your hood for mine
• fits 5th & 5.5 gens

brand new FMIC $120
• 28 x 7 x 2.5 (end cap to end cap)

PI 510 injectors $400 Sold

 

Dang man. Finally giving it up?

 

I have a little project in mind with a 350Z. I am just hungry for more power. And they make lots of parts for that car compared to ours.

 

Do you have any pics?

 

Super Chrager, water tank, piping, BOV


FMIC and pipeing

It should be completely out by the begining of this week.

 

somebody buy it. this kit is gangster.

 

Only if I had a 01... bump for a nice set up.

GL with that sale.

 

Thanks for the bumps. I may have most of it sold and then I will try selling the car again with alot less modds on it

 

is the supercharger still up for sale?

 

It may be sold, along with alot of the extras. I will know for sure in the next couple days.

 

The piping and FMIC will all fit on a 4th Gen? How abou the CAI?

 

Not sure about that. I have worked on a 4th gen but never compared it side-by-side to a 5th gen. I am working on a possible sale right now.

 

is the fmic and piping still for sale?

how about the other fmic? any other specs on that one? bar/plate , tube/fin? cfm rating etc?

 

Just the other fmic. It is a Bar/Plate. I don't remember the rating of the cfm, but I do know that it is enough for 450 hp. It has 2.5 inlet/out.

I found the specs. 25-35 psi and 600-700 CFM. added, when edited

Here are some pics... it is brand nem. I never got around to installing it.





Sitting on my bumper support, with the original FMIC still installed. not as tall as the on installed.

 

hey is this kit sold

 

Some parts will be officially on Monday. I will post then.

 

Updated list.

 

pm sent

 

replied

 

Some pics of the hood. The hood is the factory hood, that has been welded to modd it with the vents. There is no bondo or fiberglass on the hood. So it will not crack.

 

Bump for a sweet hood!! Good luck with the sale

 

that hoods $#kin sweet. howd u do it?

 

I cut into the hood support and made it as part of the frame to the hood to match the back bumper of the body kit. This way it made the hood stronger and not weaker.