Wheels/Tires Looking for a new set of shoes for your car? Check out this forum. Sponsored by X-Rims.com

FS:4 - 19x8.5 SSR Comps $350 - couple probs

Thread Tools
 
Search this Thread
 
Old Oct 1, 2009 | 09:31 AM
  #1  
NCSU_MAX's Avatar
Thread Starter
Maximoneypit
iTrader: (36)
 
Joined: Oct 2004
Posts: 21,704
From: Nashville, TN
FS:4 - 19x8.5 SSR Comps $350 - couple probs

Up for sale are my 19x8.5 et38 SSR competitions. Pictures will be up later this afternoon.

Here's the deal with these. 1 wheel is immaculate, 1 wheel has very light curb rash, 1 wheel has a smudge/scrape on the face, and one wheel is pretty screwed up with a cracked lip. The car was run off the road and smacked into a curb. The other car caused the damage to the face, and the curb cased the damage to the front and the minor rash spot on the rear. I have been told by a couple sources that because the wheel/tire still maintains pressure, it can likely be fixed. I wouldn't necessarily drive hard on it, but I did for several weeks with the lip cracked and never lost tire pressure. If you were to find 1 new/used wheel then you would have an excellent set of wheels for dirt cheap.

The tires need to be replaced - the BFG kdw2's have flat spots and the fk452's have very little life left in them.

I'm only asking $350 plus shipping because my new wheels are in and need these out of my garage. Being that the tires need to be replaced I can have them removed, but that will cost extra, and shipping them with the tires makes it much easier for packaging and roughly equal cost on shipping.

PM me with any questions - Paypal address is ghsmith@ncsu.edu
Old Oct 1, 2009 | 09:33 AM
  #2  
Mad-MAX_SE's Avatar
Still kickin'
iTrader: (2)
 
Joined: Nov 2000
Posts: 3,662
From: High Point, NC
damnit, I was logged in as my roomate...

PM's should go to me.

Pictures - the wheels are dusty/dirty since i haven't had a chance to wash the car in a week or three >.>


Good wheel:


Scuffed wheel:



Wheel with about 3-4" long light curb rash:


Last edited by Mad-MAX_SE; Oct 1, 2009 at 12:27 PM.
Old Oct 1, 2009 | 12:27 PM
  #3  
Mad-MAX_SE's Avatar
Still kickin'
iTrader: (2)
 
Joined: Nov 2000
Posts: 3,662
From: High Point, NC
Cracked wheel:

Old Oct 1, 2009 | 12:37 PM
  #4  
cardana24's Avatar
Blown
iTrader: (81)
 
Joined: May 2003
Posts: 9,762
From: Charlottesville, VA
can I have just the cracked wheel? Good luck with the sale George. Also is that the lug pattern stamped on the front of the wheel? 5x100?
Old Oct 1, 2009 | 12:49 PM
  #5  
Mad-MAX_SE's Avatar
Still kickin'
iTrader: (2)
 
Joined: Nov 2000
Posts: 3,662
From: High Point, NC
Haha, thanks bud. I honestly have no idea why they say that, even when Grant first got them I thought they sent him the wrong bolt pattern. they're definitely 5x114.3 no way they would fit with them being 5x100...
Old Oct 5, 2009 | 11:44 PM
  #6  
trand71's Avatar
Senior Member
iTrader: (3)
 
Joined: Apr 2008
Posts: 274
From: Alamosa,Co.
I like the rims, do you think i could JB weld the inner and put it on the outter and then powdercoat them? How much would shipping be to 81101? Thanks....
Old Oct 6, 2009 | 05:55 AM
  #7  
cardana24's Avatar
Blown
iTrader: (81)
 
Joined: May 2003
Posts: 9,762
From: Charlottesville, VA
Originally Posted by trand71
I like the rims, do you think i could JB weld the inner and put it on the outter and then powdercoat them? How much would shipping be to 81101? Thanks....
Please don't do that.
Old Oct 6, 2009 | 06:04 AM
  #8  
Conrad283's Avatar
I need a truck
iTrader: (2)
 
Joined: Feb 2002
Posts: 73,115
From: Naples, Fl
Originally Posted by trand71
I like the rims, do you think i could JB weld the inner and put it on the outter and then powdercoat them? How much would shipping be to 81101? Thanks....
I don't think that would be very safe.
Old Oct 6, 2009 | 06:55 AM
  #9  
Mad-MAX_SE's Avatar
Still kickin'
iTrader: (2)
 
Joined: Nov 2000
Posts: 3,662
From: High Point, NC
Originally Posted by trand71
I like the rims, do you think i could JB weld the inner and put it on the outter and then powdercoat them? How much would shipping be to 81101? Thanks....
You're going to want to send the wheel out for repair. They'll need to, i believe, heliarc weld the lip, then refinish the lip. Or you can find 1 more wheel and get 3 $600 wheels for $350 plus shipping.

The estimated shipping cost is roughly $45 a wheel to your zipcode through USPS, $55 through UPS, and $44 through FedEx.

let me know if you're still interested.
Old Oct 7, 2009 | 10:31 AM
  #10  
Mad-MAX_SE's Avatar
Still kickin'
iTrader: (2)
 
Joined: Nov 2000
Posts: 3,662
From: High Point, NC
Price drop to $300 picked up or $450 shipped obo. Need these gone.

Paypal address is ghsmith@ncsu.edu

Last edited by Mad-MAX_SE; Oct 7, 2009 at 10:47 AM.
Old Oct 13, 2009 | 06:58 AM
  #11  
Mad-MAX_SE's Avatar
Still kickin'
iTrader: (2)
 
Joined: Nov 2000
Posts: 3,662
From: High Point, NC
New week, price drop to $400 shipped, $275 picked up.
Old Oct 13, 2009 | 07:18 AM
  #12  
phatboislim's Avatar
Senior Member
iTrader: (27)
 
Joined: Jan 2006
Posts: 5,160
*SUBSCRIBED*
Old Oct 14, 2009 | 11:36 PM
  #13  
Infam0usMax's Avatar
Senior Member
 
Joined: Dec 2008
Posts: 513
From: Charleston, SC
still have these wheels? PM ME is so
Old Oct 19, 2009 | 07:20 PM
  #14  
Mad-MAX_SE's Avatar
Still kickin'
iTrader: (2)
 
Joined: Nov 2000
Posts: 3,662
From: High Point, NC
bump
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
user 11122324
5th Generation Maxima (2000-2003)
42
Jul 18, 2022 03:35 PM
BPuff57
Advanced Suspension, Chassis, and Braking
33
Apr 16, 2020 05:15 AM
My Coffee
New Member Introductions
15
Jun 6, 2017 02:01 PM
Stagnet04
4th Generation Classifieds (1995-1999)
2
Oct 11, 2015 08:16 PM
JakeOfAllTrades
7th Generation Maxima (2009-2015)
6
Oct 5, 2015 10:40 AM




All times are GMT -7. The time now is 03:30 PM.