Maxima Forums
0 2019/01/02 09:50:40
0 2019/01/03 15:53:38
0 2019/01/04 17:08:32
0 2019/01/06 17:09:08
0 2019/01/11 22:41:36
0 2019/01/11 22:41:38
0 2019/01/11 22:41:39
0 2019/01/11 22:41:39
0 2019/01/12 03:45:48
0 2019/01/12 03:45:49
So I beat a depression in the frame
So I beat a depression in the frame
0 2019/01/18 19:15:14
Next question: Are these important? What do they even do? I bought all new ones but these didn't make it when I was installing the motor.
Next question: Are these important? What do they even do? I bought all new ones but these didn't make it when I was installing the motor.
0 2019/01/18 19:15:29
First order of business: PS pulley would not clear frame...
First order of business: PS pulley would not clear frame...
0 2019/01/18 19:15:47
Sorry for out of focus, but here is the motor installed with all three engine mounts. Question here is: Will I be able to mount the tranny with the motor installed with all three of its mounts?
Sorry for out of focus, but here is the motor installed with all three engine mounts. Question here is: Will I be able to mount the tranny with the motor installed with all three of its mounts?
0 2019/01/18 19:15:59
We are clear! Hard to see, but I did the best I could. Here you can see the lower aspect of the pulley clear of the frame with the engine installed. However, there exists only approximately 1/4" to 3/8" inch clearance at the closest point to the pulley. The big question is: How much do these motors move? Will the engine torque aft enough for the pulley to make contact with the frame? Remember, I replaced all motor mounts with OEM MT mounts.
We are clear! Hard to see, but I did the best I could. Here you can see the lower aspect of the pulley clear of the frame with the engine installed. However, there exists only approximately 1/4" to 3/8" inch clearance at the closest point to the pulley. The big question is: How much do these motors move? Will the engine torque aft enough for the pulley to make contact with the frame? Remember, I replaced all motor mounts with OEM MT mounts.
0 2019/01/18 19:18:14
0 2019/01/19 12:53:46
0 2019/01/19 12:53:47
0 2019/01/19 12:53:47
0 2019/01/19 12:53:47
0 2019/01/20 00:38:58
0 2019/01/22 22:51:00
0 2019/01/23 19:22:32
0 2019/01/23 19:22:32
0 2019/01/23 19:27:48
0 2019/01/23 19:34:59
0 2019/01/23 19:35:02
0 2019/01/23 19:35:02
0 2019/01/23 19:42:46
0 2019/01/23 20:45:27
0 2019/01/23 20:45:28
0 2019/01/23 22:02:38
0 2019/01/23 22:14:29
0 2019/01/24 19:27:03
0 2019/01/24 19:27:05
0 2019/01/24 19:27:07
0 2019/01/24 19:27:07
Started on the 1/0 cables. Got one built before I quit for the day. 12 hours straight no stopping on this thing today.
Started on the 1/0 cables. Got one built before I quit for the day. 12 hours straight no stopping on this thing today.
0 2019/01/28 18:53:44
Got the S Techs in and suspension wrapped up in about 6 hours.
Got the S Techs in and suspension wrapped up in about 6 hours.
0 2019/01/28 18:53:44
Best place I could find for the engine ground.
Best place I could find for the engine ground.
0 2019/01/28 18:53:46
Starting to look like an engine bay!
Starting to look like an engine bay!
0 2019/01/28 18:53:47