Clear Blinkers!!
#1
Guest
Posts: n/a
Clear Blinkers!!
I realized after clear cornors and nice clear chrome'd headlights. the blinkers looked a little off. they were hazed had plenty of scratches and chips in them. SO I took them a apart. ripped out the secondary devider that blurred the insides even more. and wet sanded them.
i went with 220 wet/dry sand paper. super fine.
and then with a polisher i made for my drill. i went at them with Maguires plastic polish. I am VERY pleased with the result. Now that i see the amount of room i got in there. I will be retro fitting Bosch mini projectors in there as fogs. to keep the stock body lines. here are some pics
no flash
w/ flash
i went with 220 wet/dry sand paper. super fine.
and then with a polisher i made for my drill. i went at them with Maguires plastic polish. I am VERY pleased with the result. Now that i see the amount of room i got in there. I will be retro fitting Bosch mini projectors in there as fogs. to keep the stock body lines. here are some pics
no flash
w/ flash
#11
Originally Posted by heresmymind
I realized after clear cornors and nice clear chrome'd headlights. the blinkers looked a little off. they were hazed had plenty of scratches and chips in them. SO I took them a apart. ripped out the secondary devider that blurred the insides even more. and wet sanded them.
i went with 220 wet/dry sand paper. super fine.
and then with a polisher i made for my drill. i went at them with Maguires plastic polish. I am VERY pleased with the result. Now that i see the amount of room i got in there. I will be retro fitting Bosch mini projectors in there as fogs. to keep the stock body lines. here are some pics
i went with 220 wet/dry sand paper. super fine.
and then with a polisher i made for my drill. i went at them with Maguires plastic polish. I am VERY pleased with the result. Now that i see the amount of room i got in there. I will be retro fitting Bosch mini projectors in there as fogs. to keep the stock body lines. here are some pics
#17
Originally Posted by heresmymind
its these 2 little washers around a drill bit. i took a turtle waxing pad poked a hole in the middle and bwamo. pics tomorrow when i get a cam
Ok tomorrow was yesterday! Pics?
#19
Originally Posted by Gunther
Was it ColumbiaMax that posted about wiring the blinkers to have running lights? I think that would be a good combo with this.
I believe it was Maxshima94 hope I spelled his name right
#20
Originally Posted by Gunther
Was it ColumbiaMax that posted about wiring the blinkers to have running lights? I think that would be a good combo with this.
http://forums.maxima.org/showthread.php?t=525498
#26
Originally Posted by heresmymind
I wired the 194 bulbs in my corner lights to my blinkers. so that they both flash. but I am pretty sure thats been done too
http://www.geocities.com/craigbrace/
#28
I have removed the diffusers from the turns and am still unhappy with the light output. I still want to use them as turns, but hate the light output. Any chance I could upgrade the bulbs to say like a 27 watt 881? Think just blinking would generate too much heat?
I was thinking of using these:
http://www.intakeone.com/Light_bulbs...ics_Yellow.htm
I was thinking of using these:
http://www.intakeone.com/Light_bulbs...ics_Yellow.htm
#30
I did this to my blinker lenses... I polished them and removed the diffuser plate inside. It looked nice and clear like these did but when the signal was on it looked like a wimpy little bulb blinking behind the lens, so i put the diffuser plate back in
Thread
Thread Starter
Forum
Replies
Last Post
BPuff57
Advanced Suspension, Chassis, and Braking
33
04-16-2020 05:15 AM
My Coffee
New Member Introductions
15
06-06-2017 02:01 PM
doctorpullit
8th Generation Maxima (2016-)
13
04-23-2017 05:35 AM
Kyle Lee Cleveland
6th Generation Maxima (2004-2008)
1
09-28-2015 09:01 PM