3rd Generation Maxima (1989-1994) Learn more about the 3rd Generation Maxima here.

had a little accident...

Thread Tools
 
Search this Thread
 
Old Dec 6, 2001 | 04:29 PM
  #1  
Maximan190's Avatar
Thread Starter
Senior Member
iTrader: (8)
 
Joined: Oct 2001
Posts: 3,996
From: long island, NY
had a little accident...

tuesday (12/4) i was makin a U turn at an intersection and i had the green....from what i can remember there was a bus or some big rig in the left turn lane from the other side and my view was limited on the oncoming traffic......so i move out and i see a car rushing towards me and i misjudge and i hit the curb with my front right tire.....no significant visual damage except for a minor scrape on the rim and chip in the rubber on the tire. (see atchmnt) But now when i hold the steering wheel perfectly straight the car drifts to the right and sometimes ill get this knock noise when i make tight right turns. Could the algnment need to be re-adjusted or would it be something more major as, say, in the axle?
Old Dec 6, 2001 | 04:31 PM
  #2  
Maximan190's Avatar
Thread Starter
Senior Member
iTrader: (8)
 
Joined: Oct 2001
Posts: 3,996
From: long island, NY
heh btw...car is a 92se....the car is still technically driveable but the only problem i notice thus far is that drifting to the right
Old Dec 7, 2001 | 11:20 AM
  #3  
nupe500's Avatar
Jedi Knight
iTrader: (13)
 
Joined: Mar 2001
Posts: 4,610
sounds like an axle...or bearings or something to that nature....I would say alignment, but it shouldn't make any noises...I don't think

O
Old Dec 7, 2001 | 03:07 PM
  #4  
89Maxima's Avatar
Member
 
Joined: Dec 2001
Posts: 31
If your makin a right turn and there is a noise then it might be your CV Joint.
Old Dec 7, 2001 | 03:35 PM
  #5  
DanNY's Avatar
Ad·min·is·tra·tor
iTrader: (14)
 
Joined: Aug 2000
Posts: 17,724
i wouldn't say it's axle. the axle is made to bend and turn.

you prob bent a suspension component.
check the following...strut, upper strut bearing, ball joint, tie rod, sway bar and endlink.

best thing to do is pull the wheel and see.
Old Dec 7, 2001 | 05:12 PM
  #6  
Maximan190's Avatar
Thread Starter
Senior Member
iTrader: (8)
 
Joined: Oct 2001
Posts: 3,996
From: long island, NY
ok i took a better look and found out this....my front right wheel is pushed back....it scrapes against the wheel well when i make right turns
Old Dec 7, 2001 | 05:57 PM
  #7  
DanNY's Avatar
Ad·min·is·tra·tor
iTrader: (14)
 
Joined: Aug 2000
Posts: 17,724
Originally posted by Maximan190
ok i took a better look and found out this....my front right wheel is pushed back....it scrapes against the wheel well when i make right turns
time to visit the lower control arm..i would suspect it's bent.
Old Dec 10, 2001 | 11:19 AM
  #8  
89Maxima's Avatar
Member
 
Joined: Dec 2001
Posts: 31
Originally posted by DanNY


time to visit the lower control arm..i would suspect it's bent.
Same here.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Garrettz459
5th Generation Maxima (2000-2003)
15
Jul 6, 2013 07:50 PM
dr_rabias
General Maxima Discussion
27
May 8, 2011 11:05 AM
NJ3ndri
General Maxima Discussion
2
Jan 15, 2011 02:57 PM
T_Dwyer88
4th Generation Classifieds (1995-1999)
1
May 7, 2009 02:58 PM




All times are GMT -7. The time now is 03:38 AM.