4th gen part out
#1
4th gen part out
I recently totalled my 4th gen and, amongst many tears, have started to cannibalize it for some extra cash. Here's what I'll be selling, if you've got any requests let me know as I will probably send it off to the junker pretty soon.
TL retrofitted headlights with homemade harness. I spent upwards of $900 on these, they are yours for $500 plus shipping. Hella gen III ballasts, Osram 4300K bulbs, TL projectors, CE glass housings. They aren't perfect but they look and perform awesome. I was a beginner solderer when I made the harness, so it's not perfect but it has never given me any issues in a year or two or operation, 10AWG leads to the ballasts and 18AWG leads to the solenoids--lights only turn on when your corner lights/sidemarkers are on (to prevent high beam flashing when the lights are off, damaging the ballasts). You may have to push your battery back a bit and unhook something as the retrofit is flush and the projectors stick out of the back of the housing. I got a new battery that was a bit smaller (also for sale) and it just so happened to work fine without improperly fastening it. I used the aiming bracket to fasten the projectors and not the headlight housing. These headlights are awesome and IMO the best looking lights I've seen for the 4th gen, but again the housings are in fair condition with a fastener or two broken off IIRC. Took a few pics on the way out the door today:
http://img.photobucket.com/albums/v6...1/P1030729.jpg
http://img.photobucket.com/albums/v6...1/P1030730.jpg
http://img.photobucket.com/albums/v6...1/P1030756.jpg
http://img.photobucket.com/albums/v6...1/P1030758.jpg
http://img.photobucket.com/albums/v6...1/P1030760.jpg
http://img.photobucket.com/albums/v6...1/P1030761.jpg
http://img.photobucket.com/albums/v6...1/P1030763.jpg
My suspension. Ground controls with shortened Konis up front (pretty new, few thousand miles on them), regular Konis out back (many miles but no problems whatsoever). They come with Stillen camber plates and have had no problems with them. Rates are stock GC spring rates (450lbs/in up front, 365 lb/in out back). These have suffered a crash but appear to be fine. They come with strut bearings. I'm hoping to get $500 plus shipping, this is (very) arguably the best suspension setup for a 4th gen. Konis themselves typically run around $700 and I have done the work of modifying and installing them, plus you get the elusive camber plates and ground control setup. Mad tyte part-out sale pending
Eibach springs. Used, still in good condition. $100 plus shipping.
My rear sway bar. It's a Progress RSB, the fasteners are a bit bent from installation IIRC. Should have no effect on anything. $80 plus shipping.
B&M short shifter. I don't have the B&M **** any more. Sold.
'97 BCM (body control module). Car has Bose ABS (if that matters) and auto climate control. How about $80 shipped.
http://img.photobucket.com/albums/v6...1/P1030781.jpg
OEM VQ30DE MAF. Not new by any means but was in perfect working order last time I ran the engine (4 or so days ago). $50 plus shipping.
http://img.photobucket.com/albums/v6...1/P1030766.jpg
http://img.photobucket.com/albums/v6...1/P1030767.jpg
OEM Z32 shift ****, got this brand new for $75, willing to let it go for $45 plus shipping. Sale pending.
Craptastic ebay strut bar - what the hell, throw me $10 plus shipping and it's yours.
http://img.photobucket.com/albums/v6...1/P1030773.jpg
Depo corner light, driver's side - comes without bulb. $15 plus shipping.
http://img.photobucket.com/albums/v6...01/P1030724.jp
Working '97 OEM Bose HU with AUX mod--I'll even include the cupholder with the toggle switch installed. Comes with a long male 1/4" stereo minijack all soldered up waiting for your ipod/phone/laptop/whatever. Sale pending.
I'm going to hold off on selling the wheels as I will want to inspect and/or refinish them before passing them on.
Added some pics as links.
TL retrofitted headlights with homemade harness. I spent upwards of $900 on these, they are yours for $500 plus shipping. Hella gen III ballasts, Osram 4300K bulbs, TL projectors, CE glass housings. They aren't perfect but they look and perform awesome. I was a beginner solderer when I made the harness, so it's not perfect but it has never given me any issues in a year or two or operation, 10AWG leads to the ballasts and 18AWG leads to the solenoids--lights only turn on when your corner lights/sidemarkers are on (to prevent high beam flashing when the lights are off, damaging the ballasts). You may have to push your battery back a bit and unhook something as the retrofit is flush and the projectors stick out of the back of the housing. I got a new battery that was a bit smaller (also for sale) and it just so happened to work fine without improperly fastening it. I used the aiming bracket to fasten the projectors and not the headlight housing. These headlights are awesome and IMO the best looking lights I've seen for the 4th gen, but again the housings are in fair condition with a fastener or two broken off IIRC. Took a few pics on the way out the door today:
http://img.photobucket.com/albums/v6...1/P1030729.jpg
http://img.photobucket.com/albums/v6...1/P1030730.jpg
http://img.photobucket.com/albums/v6...1/P1030756.jpg
http://img.photobucket.com/albums/v6...1/P1030758.jpg
http://img.photobucket.com/albums/v6...1/P1030760.jpg
http://img.photobucket.com/albums/v6...1/P1030761.jpg
http://img.photobucket.com/albums/v6...1/P1030763.jpg
My suspension. Ground controls with shortened Konis up front (pretty new, few thousand miles on them), regular Konis out back (many miles but no problems whatsoever). They come with Stillen camber plates and have had no problems with them. Rates are stock GC spring rates (450lbs/in up front, 365 lb/in out back). These have suffered a crash but appear to be fine. They come with strut bearings. I'm hoping to get $500 plus shipping, this is (very) arguably the best suspension setup for a 4th gen. Konis themselves typically run around $700 and I have done the work of modifying and installing them, plus you get the elusive camber plates and ground control setup. Mad tyte part-out sale pending
Eibach springs. Used, still in good condition. $100 plus shipping.
My rear sway bar. It's a Progress RSB, the fasteners are a bit bent from installation IIRC. Should have no effect on anything. $80 plus shipping.
B&M short shifter. I don't have the B&M **** any more. Sold.
'97 BCM (body control module). Car has Bose ABS (if that matters) and auto climate control. How about $80 shipped.
http://img.photobucket.com/albums/v6...1/P1030781.jpg
OEM VQ30DE MAF. Not new by any means but was in perfect working order last time I ran the engine (4 or so days ago). $50 plus shipping.
http://img.photobucket.com/albums/v6...1/P1030766.jpg
http://img.photobucket.com/albums/v6...1/P1030767.jpg
OEM Z32 shift ****, got this brand new for $75, willing to let it go for $45 plus shipping. Sale pending.
Craptastic ebay strut bar - what the hell, throw me $10 plus shipping and it's yours.
http://img.photobucket.com/albums/v6...1/P1030773.jpg
Depo corner light, driver's side - comes without bulb. $15 plus shipping.
http://img.photobucket.com/albums/v6...01/P1030724.jp
Working '97 OEM Bose HU with AUX mod--I'll even include the cupholder with the toggle switch installed. Comes with a long male 1/4" stereo minijack all soldered up waiting for your ipod/phone/laptop/whatever. Sale pending.
I'm going to hold off on selling the wheels as I will want to inspect and/or refinish them before passing them on.
Added some pics as links.
Last edited by MorpheusZero; 01-29-2009 at 03:58 PM.
#10
The bus for awhile, then maybe a Civic in a month or two until I graduate (another two quarters). After that I'll start thinking about real cars again.
I really miss the old 4th gen though. Every time I hop in it's like a flashback to a few days ago when life was good.
I really miss the old 4th gen though. Every time I hop in it's like a flashback to a few days ago when life was good.
#11
#13
#15
#20
I'd prefer to sell the suspension as a whole but if you two collaborate I'll let the camber plates go for $150 and the Konis/GCs for $425. Crusher I don't have the strut nuts that came with the camber plates but I do have a method that works (the "inverted nut" as JSutter called it). It's kind of a pain to separate the suspension and the mounts, but mainly I'd just like to see the whole setup go to someone who can appreciate a proper suspension.
#22
#23
I'd prefer to sell the suspension as a whole but if you two collaborate I'll let the camber plates go for $150 and the Konis/GCs for $425. Crusher I don't have the strut nuts that came with the camber plates but I do have a method that works (the "inverted nut" as JSutter called it). It's kind of a pain to separate the suspension and the mounts, but mainly I'd just like to see the whole setup go to someone who can appreciate a proper suspension.
#27
They're on the car; I'm not up for pulling them all off though, at least not at the moment.
Edit: I'm selling the shifter on the car already anyway, so that's a no go.
Edit: I'm selling the shifter on the car already anyway, so that's a no go.
Last edited by MorpheusZero; 01-20-2009 at 09:04 PM.
#29
K I don't think Jon wants just the rear GCs so I can do this:
Rich (Mr****) can have the GCs with front konis but without camber plates and rear konis for $350
Jon (JSutter) can have the rear konis for $125
Crusher can have camber plates for $150
If that doesn't work then
Tsaulz can have GCs and Konis for $425
Crusher still gets camber plates for $150.
All prices include paypal fees but not shipping.
Any of you interested in either of these? (I know Crusher is )
Rich (Mr****) can have the GCs with front konis but without camber plates and rear konis for $350
Jon (JSutter) can have the rear konis for $125
Crusher can have camber plates for $150
If that doesn't work then
Crusher still gets camber plates for $150.
All prices include paypal fees but not shipping.
Any of you interested in either of these? (I know Crusher is )
#32
The ride is firm (coilover firm) but I loved every second of it. If you want the suspension without the camber plates (crusher is pretty hell bent on 'em) we could work something out. I really just want to get this stuff out of here and scrounge up some dough so I can move onto something else.
#34
#36
#38