4th Generation Maxima (1995-1999) Visit the 4th Generation forum to ask specific questions or find out more about the 4th Generation Maxima.

A few problems I need help with...

Thread Tools
 
Search this Thread
 
Old 07-23-2007, 11:50 AM
  #1  
Member
Thread Starter
 
Noladol's Avatar
 
Join Date: Oct 2006
Location: Austin, TX
Posts: 240
A few problems I need help with...

I have looked around and could not find a thread that helped me, therefore I am making this thread.

The first problem is when my car has been sitting for a while I have to push the gas pedal for it to start and it's an automatic so I shouldnt have to do that. It runs pretty rough when it does start so I give it a little gas and it starts to idle normally.

The second problem is that when my car is warming up, I get a grinding noise and it sounds like it's coming from the belts, but maybe not necessarily the belts making that sound? It seems to go away when the engine is warmed up.

And NO, my check engine light is not on, however, every now and then when I do try to start my car it seems like a code is trying to display(blinkers flash a few times, etc) but it stops once my car begins to start. So I think my check engine light wants to come on, but I dont really know what the hell.

Help please. =o)
Noladol is offline  
Old 07-23-2007, 12:30 PM
  #2  
What's next!?..
iTrader: (10)
 
JPMax's Avatar
 
Join Date: May 2002
Location: Edison, NJ
Posts: 1,282
Have you done anything to try and solve the problem yet?

Could a be a few things that can cause trouble starting, but from what you've described I'm leaning towards a bad starter motor.

The grease inside them dries up after several years and gums up the internal parts. When the car is cold, it will make a grinding Errrr kinda noise when you try to start it and sometimes take a few seconds of holding the gas down a bit to keep the engine from stalling. The noise should be coming from the driver's side of the engine. Easy enough to replace yourself. See the FAQs.
JPMax is offline  
Old 07-23-2007, 01:34 PM
  #3  
Member
Thread Starter
 
Noladol's Avatar
 
Join Date: Oct 2006
Location: Austin, TX
Posts: 240
It was recently replaced and it was happening before the motor was replaced also. No, the sound is coming from the passenger side near the belts.
Noladol is offline  
Old 07-23-2007, 04:24 PM
  #4  
dot dot dot ...
iTrader: (22)
 
NmexMAX's Avatar
 
Join Date: Dec 2000
Location: Santa Fe, NM
Posts: 34,588
Have you tried checking for ECU codes?
http://forums.maxima.org/showthread.php?t=104931
NmexMAX is offline  
Old 07-23-2007, 05:14 PM
  #5  
No more Maximas...
iTrader: (26)
 
pmohr's Avatar
 
Join Date: Jul 2005
Location: Oak Ridge, TN
Posts: 14,331
Originally Posted by Noladol
The first problem is when my car has been sitting for a while I have to push the gas pedal for it to start and it's an automatic so I shouldnt have to do that.
That part confuses me.

Originally Posted by Noladol

And NO, my check engine light is not on, however, every now and then when I do try to start my car it seems like a code is trying to display(blinkers flash a few times, etc) but it stops once my car begins to start. So I think my check engine light wants to come on, but I dont really know what the hell.
Is it the CEL blinking or the O/D light? If the CEL is blinking, it would be a misfire (aren't there different classifications for those? Diff levels of misfires or something, I know NmexMax knows, he'll be in here as soon as he sees I've posted here ).
pmohr is offline  
Old 07-24-2007, 10:07 AM
  #6  
Member
Thread Starter
 
Noladol's Avatar
 
Join Date: Oct 2006
Location: Austin, TX
Posts: 240
Nevermind. I was just stating the obvious.

Another thing I forgot to mention was that everytime my car starts, it sounds like a belt squeeks really loud just for a second or so. It may be the belt, it may not. I would just like to get some opinions before I take it to the shop is all.
Noladol is offline  
Old 07-24-2007, 10:17 AM
  #7  
Member
Thread Starter
 
Noladol's Avatar
 
Join Date: Oct 2006
Location: Austin, TX
Posts: 240
Originally Posted by NmexMAX
Have you tried checking for ECU codes?
http://forums.maxima.org/showthread.php?t=104931
No, I will def. try that tonight though.
Noladol is offline  
Old 07-25-2007, 01:20 PM
  #8  
Member
Thread Starter
 
Noladol's Avatar
 
Join Date: Oct 2006
Location: Austin, TX
Posts: 240
Anyone? Come on this is maxima.org
Noladol is offline  
Old 07-25-2007, 01:26 PM
  #9  
Senior Member
iTrader: (36)
 
MaxGordon7's Avatar
 
Join Date: Jan 2005
Location: SE Wisconsin
Posts: 1,194
belt noise is cuz your belts are little lose. As for no waiting to start, id clean out the throttle body, take it off and really clean it if your up for it. Check plugs. Seems like might be carbon built up or the ivac is not set up correctly.
MaxGordon7 is offline  
Old 07-25-2007, 01:30 PM
  #10  
Senior Member
 
Peebs187's Avatar
 
Join Date: May 2007
Posts: 136
The noise is likely a bearing starting to fail in an accessory or pulley, and may quiet down once it heats up and expands. The starting issue could be so many things, If there is no CEL, you may need to do some serious houskeeping and clean some carbon and buildup, you may have a dirty fuel filter/ fuel problem, vacuum leak, and the list could go on.... Try doing some problem solving and narrow it down a bit.
Peebs187 is offline  
Old 07-25-2007, 03:36 PM
  #11  
Member
Thread Starter
 
Noladol's Avatar
 
Join Date: Oct 2006
Location: Austin, TX
Posts: 240
Thank you so much. Can you direct me to a link maybe that shows me exactly what to clean? I just got some carb cleaner so im ready to go.
Noladol is offline  
Old 07-30-2007, 08:04 AM
  #12  
Member
Thread Starter
 
Noladol's Avatar
 
Join Date: Oct 2006
Location: Austin, TX
Posts: 240
Is there a link?
Noladol is offline  
Old 07-30-2007, 09:19 AM
  #13  
Senior Member
iTrader: (1)
 
heynow's Avatar
 
Join Date: Aug 2006
Posts: 1,132
FAQs my good man. Reading can be very enlightning!
heynow is offline  
Old 07-30-2007, 03:46 PM
  #14  
Junior Member
 
Liso's Avatar
 
Join Date: Jun 2007
Posts: 20
Let me ask you a few questions. When was the last time your car got a complete tune-up? You know, plugs, air filter, fuel filter, cleaning the throttle body? All those things will affect the way your car runs. Also, as it has been mentioned, scan the car for codes and go from there.
Liso is offline  
Old 07-31-2007, 10:20 AM
  #15  
Member
Thread Starter
 
Noladol's Avatar
 
Join Date: Oct 2006
Location: Austin, TX
Posts: 240
Originally Posted by Liso
Let me ask you a few questions. When was the last time your car got a complete tune-up? You know, plugs, air filter, fuel filter, cleaning the throttle body? All those things will affect the way your car runs. Also, as it has been mentioned, scan the car for codes and go from there.
New NGK Iridium plugs about 4 months ago(along with 6 new ignition coils! ), also have a K&N air filter that can be cleaned whenever, fuel filter is a great suggestion and also cleaning the throttle body is a great suggestion. I know how to change the fuel filter, but my next step is how to clean the throttle body. I will do these things this week and get back to you when they are complete. Thanks!!!
Noladol is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
litch
4th Generation Maxima (1995-1999)
123
01-04-2024 07:01 PM
jmlee44
4th Generation Maxima (1995-1999)
8
10-02-2022 02:13 PM
hcarter1112
5th Generation Maxima (2000-2003)
42
07-18-2022 03:35 PM
gavin68
5th Generation Maxima (2000-2003)
8
09-18-2021 12:36 PM
HerpDerp1919
3rd Generation Maxima (1989-1994)
2
09-29-2015 02:02 PM



Quick Reply: A few problems I need help with...



All times are GMT -7. The time now is 02:26 PM.