Smoked Tail Lights
He did some nice tinting of his tail lights:
http://www.cardomain.com/id/deckdout2
You could also just buy 2000-2001 SE tails and tint em even more.... they are a straight swap if you get em with all the harnesses.
http://www.cardomain.com/id/deckdout2
You could also just buy 2000-2001 SE tails and tint em even more.... they are a straight swap if you get em with all the harnesses.
Originally Posted by JD2k2
oh come on, what's wrong with the 02-03 tailights 

Like so:
Mine (01 SE tails)

Deckdout2 (DIY tinted tails)
Originally Posted by Puppetmaster
Nothing, but I do think that they only look good with lighter colors, like yours, and the darker colors look good with either tinted tails or the 00-01 SE tails...
Like so:
Mine (01 SE tails)

Deckdout2 (DIY tinted tails)

Like so:
Mine (01 SE tails)

Deckdout2 (DIY tinted tails)

Originally Posted by Starchild2K2SE
Do you just spray them right over on the tailights? Or do you open them up and spray them. I have the tint spray, and I want to do this mod, but I dont want my car to look stupid....
Originally Posted by Starchild2K2SE
Do you just spray them right over on the tailights? Or do you open them up and spray them. I have the tint spray, and I want to do this mod, but I dont want my car to look stupid....
spray one coat... then use hair dryer.... then do it over untill u like the finish....
Holy crap... are you sure that was tint and not black paint? I sure hope the cops are forgiving by where you live....
The pics are blurry, but it looks like a clean job from what I can tel...
The pics are blurry, but it looks like a clean job from what I can tel...
LOL yea i looks pitch black but its really transluscent ,,, i'll post pics at night time.... can i get pulled over during the daytime for it being to black????
Damnn now i need limo tint to match it
Damnn now i need limo tint to match it
How did you black out your headlights? Please tell me.LOL.
1) You remove headlights
2)there are like 3 tiny screw on the back of headlight remove them all.
(you can leave the HID ballast alone)
3) Use hairdyer start heating all around the sides when its hot enough heat one side only and try to pry it open while heating (two people required)
4) do that untill the whole cover come of.
5) tape up light assembly and paint.. i used glossy finish.
here's a good thing to remember while scoping out cops. i was a little worried myself when i first did mine. regardless of what time of day it is, always run your parking lights when you drive. by the looks of your pics with the lights on, it shines through well enough for them to not bother you. i've had them right up on me in broad daylight, and (knock on wood) have yet to have any issues. try that and you should be ok.
btw, very nice on the tails....i think that dark would probably look good on my black. let me ponder a little......
btw, very nice on the tails....i think that dark would probably look good on my black. let me ponder a little......
Originally Posted by eyecon7
Will LED bulbs make it brighter..... i was thinking bout doing that even b4 i smoked it
Originally Posted by Deckdout2
I've never tried leds, but i think with the effect it puts out it will probably look good. give it a try, you're only out a few bucks. www.autolumination.com
Originally Posted by eyecon7
what color LED did u use
for the rear break lights i used the Size 7443 Power Tower http://autolumination.com/7443_7440.htm

$17.99 EACH
total with shipping and handling was $38.48
PROBLEMS-LIGHT OUT LIGHT ON DASH COMES ON WHEN BREAK IS APPLIED OR PARKING/HEADLIGHTS ARE ON
SOLUTION-NONE (LOAD EQUALIZER WILL HEAT UP TOO MUCH AND MELT HOUSEING)
For the front Directionals i used
15 LED Size 7440 Amber http://autolumination.com/7443_7440.htm

$9.99 EACH
Total with shipping and handling was $22.48
Problems-DIRECTIONAL RAPIDLY BLINKED TO SIGNAL LIGHT WAS OUT
SOLUTION- 3 Ohm Load Equalizer.
3 Ohm Load Equalizer http://autolumination.com/equalizers.htm

Installation- spliced and grounded to each positive directional wire (one for each side, capapble of handling a front and rear led directional bulb)
$8.99 each
Total with shipping and handling was $20.48
TOTAL LED PROJECT COST (FRONT AND REAR DIRECTIONALS AND BREAK LIGHTS) $103.92!
WHOLE DISCRIPTION AND PICTURES OF THE BULBS IN USE ON MY CAR DOMAIN SITE, CHECK IT OUT http://www.cardomain.com/ride/834850/6
heres my theory first of all u dont have a red reflector that makes a huge Diff ure lights are like the new RX330 rear tail they have no reflectors... i just want to know which is brighter LED or Bulb
Thread
Thread Starter
Forum
Replies
Last Post
fastcarny
5th Generation Maxima (2000-2003)
2
Oct 6, 2015 10:42 AM
ballerchris510
3rd Generation Maxima (1989-1994)
9
Sep 10, 2015 09:35 PM
-ReLLiK-
4th Generation Classifieds (1995-1999)
0
Sep 8, 2015 12:02 PM
Maxima30
5th Generation Maxima (2000-2003)
2
Sep 7, 2015 06:13 PM






