Post up Photos of your 2000-2001 Engine Bay
#1
Old Maxima Legend
Thread Starter
iTrader: (16)
Join Date: Apr 2003
Location: Paraparaumu, NZ
Posts: 6,069
Post up Photos of your 2000-2001 Engine Bay
Post up any hi-resolution or large photos of your 2000-2001 Maxima engine bay. Like to see how the setups are looking. Stock photos would be great too.
#2
Originally Posted by Ceasars Chariot
Post up any hi-resolution or large photos of your 2000-2001 Maxima engine bay. Like to see how the setups are looking. Stock photos would be great too.
60': 2.147
1/8: 9.029
1/8 MPH: 77.38
1000: 11.707
1/4: 13.979
1/4 MPH: 98.87 <------you did this is a 4 gen?!?!?!?
#3
Originally Posted by Ceasars Chariot
Post up any hi-resolution or large photos of your 2000-2001 Maxima engine bay. Like to see how the setups are looking. Stock photos would be great too.
#19
Originally Posted by n3985
Holy ground wires! What are all those connected to?
#20
Originally Posted by BlackBIRDVQ
One goes to the TPS, another one to the stock grounding point, then you got the starter, to the alternator, the 2 grounding points by the oil cap, and some other ones.... it made the dash lights much brighter after wards- only diff I can tell from doing this. I might ground out my Emanage Ultimate similar way along with the ECU.... I dunno yet.
Damn, I'm gonna have to re-do them in bright orange!
#31
Originally Posted by MaxBoost925
Naw mang. I got camber plates
me too.
Steven, it's holding up fine...haven't checked the level. Maybe I'll look this weekend and see how much it's collected...
#32
Old Maxima Legend
Thread Starter
iTrader: (16)
Join Date: Apr 2003
Location: Paraparaumu, NZ
Posts: 6,069
Originally Posted by FriscoMaxima
offtipic, but...
60': 2.147
1/8: 9.029
1/8 MPH: 77.38
1000: 11.707
1/4: 13.979
1/4 MPH: 98.87 <------you did this is a 4 gen?!?!?!?
60': 2.147
1/8: 9.029
1/8 MPH: 77.38
1000: 11.707
1/4: 13.979
1/4 MPH: 98.87 <------you did this is a 4 gen?!?!?!?
#33
Old Maxima Legend
Thread Starter
iTrader: (16)
Join Date: Apr 2003
Location: Paraparaumu, NZ
Posts: 6,069
thanks for the photos, many of you may know lots of the 4th gen guys are now swaping out upper intake manifold for the 2000-2001 upper intake manifold that are on your cars.
wanted to have a look at them in the 5th Gens. Surprisingly though, I have not seen this cover that I have seen on so many photos in this thread ? is this some sort of aftermarket piece ?
Looks real good though. Im going with the Upper and lower intake manifolds off a 2000 model maxima, you guys make what 220 hp at 6500 rpms, i was laughing at my dyno the other day at around 5500 rpms I put up 196 hp but drop off dead and was around 150-155 hp at 6500 rpms, so that will be a huge power boost im looking forward too, and again thanks for the photos !
wanted to have a look at them in the 5th Gens. Surprisingly though, I have not seen this cover that I have seen on so many photos in this thread ? is this some sort of aftermarket piece ?
Looks real good though. Im going with the Upper and lower intake manifolds off a 2000 model maxima, you guys make what 220 hp at 6500 rpms, i was laughing at my dyno the other day at around 5500 rpms I put up 196 hp but drop off dead and was around 150-155 hp at 6500 rpms, so that will be a huge power boost im looking forward too, and again thanks for the photos !
#34
Originally Posted by Ceasars Chariot
wanted to have a look at them in the 5th Gens. Surprisingly though, I have not seen this cover that I have seen on so many photos in this thread ? is this some sort of aftermarket piece ?
#39
heres my engine bay
the only changes i've done so far are, nismo oil cap, nismo radiator cap, trans flush and cleaned magnets with new filter and gasket, oil change to mobile 5000, mobile 1 oil filter, ngk iridium spark plugs, optima red top, 1guage big 3, plus some 4 guage from place to place and a stock k & n filter
am i the only one whos flipped the location of my positive and negative battery cables on my maxima?
the only changes i've done so far are, nismo oil cap, nismo radiator cap, trans flush and cleaned magnets with new filter and gasket, oil change to mobile 5000, mobile 1 oil filter, ngk iridium spark plugs, optima red top, 1guage big 3, plus some 4 guage from place to place and a stock k & n filter
am i the only one whos flipped the location of my positive and negative battery cables on my maxima?