Well, I lost alot of oil due to a faulty oil psi switch and ended spinning a bearing so, new motor is going in. Cams are being sold.

If needed, i will sale the cam adapters with them so you can use them in a 3.0 or use the adapters for a 3.5swap.

its a 260/260 deg. duration with a 10.9mm lift
Selling for $500 obo with the adapters.(shipped)

 

The link is broken, mate.

 

MODS, can you move this to the general FS section please.

Thanks

 

Done. Even fixed the spelling.

 

any pics ? JWT SYTLE ? so these are knock offs ?

 

no pics as of yet. They are still in the motor. Going to start on the tear down today. But yes. they are the knock offs. I had a video of the idle but something happened to the link. Going to take another video today of the idle and post it up in about 3-5hours.

 

are these just regrinds or acutal company that makes jwt knock offs ? Is there more specs on these?

 

Deluboz is the company.
I believe Jime had a writeup of the satisfaction with these cams.

Spec
260 Degrees Duration / .428" (10.9MM) Lift (Intake Cam.Advanced 2 Degrees)

Cold Valve Lash .010-.013" on Intake & Exhaust

link to place where they were bought from
http://cgi.ebay.com/ebaymotors/JDM-P...QQcmdZViewItem

 

PM'ed ya

 

videos:

this is the noise coming from TC


exhaust note on cold idle

 

MMM Interested in how these cams are?

 

Hey ghost, I've got a set of those installed in my 3.5 '99, and they work very well. Were you able to bolt your cams in without changing any of the cam buckets? I was lucky with my install - everything within .001 " of spec. Used Stephen's cam adapters and no problems there.

Bad luck on your oil leak.

 

Can you confirm that the cams have not been damaged as a result of the oil pressure loss?

 

stock cam buckets and yes nismology, I will pop the valve cover off when I get home and take pics. ill have the whole cam out by.........sat-sun as long as there is no rain

 

How do these cams fair with boosted applications? Is this lift/duration geared for a more N/A setup, or still good gains can be had with forced induction?

 

You must not have read all of it...

 

bump bump bump

 

gemmie two weeks

 

i'm interested in these, but i would like to have my question above answer prior to moving forward. thanks.

 

They are fine for boosted apps. Plenty of examples over on my350z. They are, after all, on the mild side of the spectrum no matter the application.

 

Preciate that. I'm not well versed in cams regarding specs and demographics. When I was looking a while back I knew different specs worked better (saw more gains) with specific applications, but couldn't recall that info (subscribed thread).

Will do more soul searching and advise decision. Thanks.

 

If you do decide to get a more aggressive grind, please be advised that the price will jump up by a few hundred (at the least) since these are knock-offs.

 

$400obo shipped

bumpity bump bump..Ill give a few more weeks before I decide to keep them and install on my 3.5 swap

 

I wouldn't need to use the cam adapters if I'm installing these directly in a 3.5 correct? Only if they were going in a 3.0 and/or 3.5 swap?

I'm still debating back and forth, looking at this thread everyday, just haven't made up my mind yet. Sorry so slow.

 

Dun!

 

^^ Please make sure your installer verifies the valve clearance is correct before buttoning it up for good.


Congrats!

 

I will confirm.

Can't wait! Thanks sir.

 

i need the adapters

 

I already have adapters...would you sell just the cams? if so, how much?

edit: wait...are these sold?

 

I belive these are sold

 

yes, dey be sold.