***PICS*** Installed Clear Spoiler LED
05-10-2003, 11:10 AM
#1
Senior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2001
Location: Long Island, NY
Posts: 3,432
***PICS*** Installed Clear Spoiler LED
Thanks to K Pazzo 6 for all the necessary info, I was able to add a mod that is quite rare for a Maxima.
I bought the clear spoiler LED brake light HERE and had to modify it slightly to replace my stock red spoiler LED. Install took me about an hour start to finish.
Check K Pazzo 6's homepage for the How-To on this...
Here's a few pics (I know, she is filthy):
-Tony
I bought the clear spoiler LED brake light HERE and had to modify it slightly to replace my stock red spoiler LED. Install took me about an hour start to finish.
Check K Pazzo 6's homepage for the How-To on this...
Here's a few pics (I know, she is filthy):
-Tony
05-10-2003, 11:25 AM
#4
Senior Member
Join Date: Jun 2002
Posts: 1,868
Re: ***PICS*** Installed Clear Spoiler LED
Originally posted by araffio
Thanks to K Pazzo 6 for all the necessary info, I was able to add a mod that is quite rare for a Maxima.
I bought the clear spoiler LED brake light HERE and had to modify it slightly to replace my stock red spoiler LED. Install took me about an hour start to finish.
Check K Pazzo 6's homepage for the How-To on this...
Thanks to K Pazzo 6 for all the necessary info, I was able to add a mod that is quite rare for a Maxima.
I bought the clear spoiler LED brake light HERE and had to modify it slightly to replace my stock red spoiler LED. Install took me about an hour start to finish.
Check K Pazzo 6's homepage for the How-To on this...
btw, is the tip on your car from the obx, or did you put on a different tip. its looks a little larger than the obx
05-10-2003, 11:50 AM
#6
Senior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2001
Location: Long Island, NY
Posts: 3,432
Re: Re: ***PICS*** Installed Clear Spoiler LED
Originally posted by DTR Maxima
looks good. i think i might do that and tint it when i tint my red/clears.
btw, is the tip on your car from the obx, or did you put on a different tip. its looks a little larger than the obx
looks good. i think i might do that and tint it when i tint my red/clears.
btw, is the tip on your car from the obx, or did you put on a different tip. its looks a little larger than the obx
05-10-2003, 12:12 PM
#11
Originally posted by araffio
It was covered with pollen...early spring sucks
It was covered with pollen...early spring sucks
05-10-2003, 01:04 PM
#15
Originally posted by araffio
Kirk- Get a California duster, works wonders on pollen and dust, especially if the car has a fresh coat of wax on it.
Kirk- Get a California duster, works wonders on pollen and dust, especially if the car has a fresh coat of wax on it.
05-10-2003, 01:22 PM
#16
Senior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2001
Location: Long Island, NY
Posts: 3,432
Originally posted by D-sta
One day I have to go to DPA and see it in person. You have one of the nicest 4th gens. When I go to DPA with N34JZ i'll see it.
One day I have to go to DPA and see it in person. You have one of the nicest 4th gens. When I go to DPA with N34JZ i'll see it.
Thanks...I'm usually up there on Fri or Sat if the weather is nice
05-10-2003, 11:47 PM
#19
Senior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2001
Location: Long Island, NY
Posts: 3,432
Originally posted by scmaxima2k
hey i just ordered my clear LED today and i was just wondering which method u used to install it. Did u drill new holes or just use the silicone to make it stick? looks good btw
-Steve
hey i just ordered my clear LED today and i was just wondering which method u used to install it. Did u drill new holes or just use the silicone to make it stick? looks good btw
-Steve
Only drilled a hole to run the wires.
05-11-2003, 06:02 PM
#27
Senior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2001
Location: Long Island, NY
Posts: 3,432
Can you explain how you got the housing open? I wanted to paint the brown circuit board either white or silver, but I couldn't figure out how to get the housing open.
Thanks. I'd like to do this...
Thanks. I'd like to do this...
05-11-2003, 06:08 PM
#28
Originally posted by araffio
I was going to try that, but I couldn't see how the housing could be opened up. The brown circuit board bothered me too, but I thought I had to live with it. How did you get it opened? I'll do this next weekend probably.
I was going to try that, but I couldn't see how the housing could be opened up. The brown circuit board bothered me too, but I thought I had to live with it. How did you get it opened? I'll do this next weekend probably.
05-11-2003, 07:00 PM
#33
Senior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2001
Location: Long Island, NY
Posts: 3,432
Originally posted by Maxman2000
I got the first step done araffio on page 7 of my homepage if you want to see it. It's the step to cut through the glue.
I got the first step done araffio on page 7 of my homepage if you want to see it. It's the step to cut through the glue.
Thanks...
the pic isn't loading though
looks hott Tone!
05-12-2003, 02:56 PM
#40
a guy from electrodyne called me today and said my clear spoiler LED is on backorder and they arent expecting them for 6 weeks. THEN the wheels i want arent gonna be available at tirerack until the end of June.....not a good day.....-Steve