NEED HELP: "MSD" Rpm Window Switch install
Re: Re: NEED HELP: "MSD" Rpm Window Switch install
Originally posted by Keven97SE
Errr, uhhh, ...
you want your windows to automatically roll up at a certain rpm?
?!?!?!
Errr, uhhh, ...
you want your windows to automatically roll up at a certain rpm?
?!?!?!
BWAHAHAHAHAHA....thats classic!!!!
Re: NEED HELP: "MSD" Rpm Window Switch install
Originally posted by My 4DSC
Where do I tap in for the RPM signal for the switch?
THANKS IN ADVANCE!
Adam
Where do I tap in for the RPM signal for the switch?
THANKS IN ADVANCE!
Adam
Old Fuddy Duddy
Joined: Feb 2001
Posts: 2,712
Re: NEED HELP: "MSD" Rpm Window Switch install
Originally posted by My 4DSC
Where do I tap in for the RPM signal for the switch?
THANKS IN ADVANCE!
Adam
Where do I tap in for the RPM signal for the switch?
THANKS IN ADVANCE!
Adam
And it will roll up your windows when you want too!
Is it for NOS or other top secret project?
Guest
Posts: n/a
Re: Re: NEED HELP: "MSD" Rpm Window Switch install
Originally posted by Colonel
Check IceY2k1 page as well. On a 2K1 I believe it is the left dash connector and a WHITE with GREEN stripe wire which is to the left of the green with silver dashes and to the right of the red wire.
Is it for NOS or other top secret project?
Check IceY2k1 page as well. On a 2K1 I believe it is the left dash connector and a WHITE with GREEN stripe wire which is to the left of the green with silver dashes and to the right of the red wire.
Is it for NOS or other top secret project?
what is a "left dash connector" & where is it located?
yes it is for NOS...
ME??...top secret projects??
Old Fuddy Duddy
Joined: Feb 2001
Posts: 2,712
Re: Re: Re: NEED HELP: "MSD" Rpm Window Switch install
Originally posted by My 4DSC
huh?
what is a "left dash connector" & where is it located?
yes it is for NOS...
ME??...top secret projects??
huh?
what is a "left dash connector" & where is it located?
yes it is for NOS...
ME??...top secret projects??
Check out this weblink courtesy of IceY2k1:
Ice's Shift light install pictures
Guest
Posts: n/a
Re: Re: Re: Re: NEED HELP: "MSD" Rpm Window Switch install
Originally posted by Colonel
When you remove the dash trim and CAREFULLY tip the gauge cluster over, you will see THREE connectors at the back of the cluster (1 white 2 brown). As you are sitting in the seat looking at the cluster, its the connector on the left side.
Check out this weblink courtesy of IceY2k1:
Ice's Shift light install pictures
When you remove the dash trim and CAREFULLY tip the gauge cluster over, you will see THREE connectors at the back of the cluster (1 white 2 brown). As you are sitting in the seat looking at the cluster, its the connector on the left side.
Check out this weblink courtesy of IceY2k1:
Ice's Shift light install pictures
Joined: Aug 2000
Posts: 6,344
Is it modified by MSD for one cylinder application? If not, it's not going to work. Easiest way to get the tach wire is from the ignition signal at the coil pack. There are three wires to each of the coil pack. It's the wire (color with stripe) that shows .01V -.1V when the ignition switch is at the on position and the car is not running. The other wire is ~+12V(red) and the other one is ground(black).
Thread
Thread Starter
Forum
Replies
Last Post
vingodine
5th Generation Classifieds (2000-2003)
45
May 21, 2016 12:46 PM
MaximaDrvr
7th Generation Maxima (2009-2015)
16
Aug 19, 2015 08:20 PM
shaunkey1
5th Generation Maxima (2000-2003)
4
Aug 18, 2015 10:09 PM
kjm900r
4th Generation Maxima (1995-1999)
6
Aug 5, 2015 07:14 AM