E30 update
Hah. It's not all that much of a looker, but I like the inner beauty more 
M50NV and lightweight flywheel
Rebuilt Z3 shifter with delrin bushings
3.73 LSD
UUC Swaybars
Stock suspension for now for the "slow POS" look
Quicker E36 steering rack and new tie rods
New LCAs and M3 offset control arm bushings for moar caster
E32 7 series brake booster and master cylinder, rebuilt calipers and new textar pads/brembo blanks all around
14" basketweaves with 195/60 RT615s
...Says the guy still stuck in the 4th gen...

M50NV and lightweight flywheel
Rebuilt Z3 shifter with delrin bushings
3.73 LSD
UUC Swaybars
Stock suspension for now for the "slow POS" look
Quicker E36 steering rack and new tie rods
New LCAs and M3 offset control arm bushings for moar caster
E32 7 series brake booster and master cylinder, rebuilt calipers and new textar pads/brembo blanks all around
14" basketweaves with 195/60 RT615s
...Says the guy still stuck in the 4th gen...
Last edited by MorpheusZero; Jan 19, 2010 at 11:37 AM.
Hah. It's not all that much of a looker, but I like the inner beauty more 
M50NV and lightweight flywheel
3.73 LSD
UUC Swaybars
Stock suspension for now for the "slow POS" look
Quicker E36 steering rack and new tie rods
New LCAs and M3 offset control arm bushings for moar caster
E32 7 series brake booster and master cylinder, rebuilt calipers and new textar pads/brembo blanks all around
14" basketweaves with 195/60 RT615s

M50NV and lightweight flywheel
3.73 LSD
UUC Swaybars
Stock suspension for now for the "slow POS" look
Quicker E36 steering rack and new tie rods
New LCAs and M3 offset control arm bushings for moar caster
E32 7 series brake booster and master cylinder, rebuilt calipers and new textar pads/brembo blanks all around
14" basketweaves with 195/60 RT615s
Can looks great. Good job on the swap.
That's what's in the car right now (never would have guessed, right?). Future plans are to clean up the swap more, then the crack free dash, GC coilover kit/Konis that's all sitting in my room, but first I need springs, camber plates and new wheel bearings, not to mention a skid plate, and to rebuild the rear suspension with adjusters so the alignment isn't fubar'd when I lower it. Then maybe I get a new hood, cut out a spot of rust, 15 or 16x8s and make it look pretty.
Somewhere in there I might start losing stuff like power steering, trunk tar etc to lighten it up a little. I think the PS pump is on its way out anyway.
Somewhere in there I might start losing stuff like power steering, trunk tar etc to lighten it up a little. I think the PS pump is on its way out anyway.
Patience young padawan. 
Just ordered a Mark D chip (good improvement and raised rev limiter), when I get the O2 sensor in, the intake on the right side of the heat shield, and the chip installed I'll take a real speedo vid. It's not stupid fast, but it's quick enough to be damn fun.

Just ordered a Mark D chip (good improvement and raised rev limiter), when I get the O2 sensor in, the intake on the right side of the heat shield, and the chip installed I'll take a real speedo vid. It's not stupid fast, but it's quick enough to be damn fun.
Patience young padawan. 
Just ordered a Mark D chip (good improvement and raised rev limiter), when I get the O2 sensor in, the intake on the right side of the heat shield, and the chip installed I'll take a real speedo vid. It's not stupid fast, but it's quick enough to be damn fun.

Just ordered a Mark D chip (good improvement and raised rev limiter), when I get the O2 sensor in, the intake on the right side of the heat shield, and the chip installed I'll take a real speedo vid. It's not stupid fast, but it's quick enough to be damn fun.
Thread
Thread Starter
Forum
Replies
Last Post
litch
4th Generation Maxima (1995-1999)
123
Jan 4, 2024 07:01 PM
mkaresh
8th Generation Maxima (2016-)
21
Mar 12, 2018 06:48 PM
KabirUTA13
5th Generation Classifieds (2000-2003)
19
Oct 17, 2015 02:15 AM








