CPS (ref) wire harness help.
CPS (ref) wire harness help.
Just recently I got a code (0407) and thought 
since I just replaced the sensor less than a year (20k) ago. So I go under and see what was going on there, and to my surprise 
I see that the harness to the CPS (ref) is mangled and chewed up by the acc.belt. It's only about 12" long and connects to the CPS, and has another larger connector on the other side behind the oil fitler.
So after searching for it online for a while, as it's only about a ft in length, but come to a conclusion that it's sold with the "main ECU harness".
Has anyone ever had similar experiences?
since I just replaced the sensor less than a year (20k) ago. So I go under and see what was going on there, and to my surprise I see that the harness to the CPS (ref) is mangled and chewed up by the acc.belt. It's only about 12" long and connects to the CPS, and has another larger connector on the other side behind the oil fitler. So after searching for it online for a while, as it's only about a ft in length, but come to a conclusion that it's sold with the "main ECU harness".
Has anyone ever had similar experiences?
OMG OMG OMG!!! NMex is actually ASKING a question instead of answering them!!
I just pulled and cleaned that CPS sensor two weekends ago... but I didn't look at the harness closely.
I just took a look in Nissan FAST briefly but couldn't identify that part of a harness as a seperate P/N.. I gotta run for now - but I can look again when I get back if you still need.
I just pulled and cleaned that CPS sensor two weekends ago... but I didn't look at the harness closely.
I just took a look in Nissan FAST briefly but couldn't identify that part of a harness as a seperate P/N.. I gotta run for now - but I can look again when I get back if you still need.
Yup, finally asking a ? nj, I would appreciate it if you could do that for me... This hard strating is pissing me off.
I searched and there's a similar thread, looks like a quick reference from the FSM wiring diagram and I should be good to go with a little self siwring job. Although I found a complete harness from www.car-part.com for ~ 80$, I can use what I need, but then I'll have an incomplete harness with no use for it. Then again, I could replace any other damaged areas I may find on my 10 y/o 230k beast ... so it's sort of a tough decision right now.
I searched and there's a similar thread, looks like a quick reference from the FSM wiring diagram and I should be good to go with a little self siwring job. Although I found a complete harness from www.car-part.com for ~ 80$, I can use what I need, but then I'll have an incomplete harness with no use for it. Then again, I could replace any other damaged areas I may find on my 10 y/o 230k beast ... so it's sort of a tough decision right now.
The FAST software is really tedious to use until you get used to it and I'm not very good at it yet... I found the CPS schematic but no harnesses are shown there... I'll be online again in 2 hours or so.. I'll post back with what I'm able to dig up then (if you haven't already got the answer).
Do you have the FSM?
Do you have the FSM?
Dont know if I'm crazy but I cant dig up a schematic for the CPS in the FSM.
I'm still in shock Nmex is asking a question!
but in all seriousness what do you need help with Nmex? you need the wiring diagram of the CPS (Ref)?
I'm still in shock Nmex is asking a question!
but in all seriousness what do you need help with Nmex? you need the wiring diagram of the CPS (Ref)?
Originally Posted by NmexMAX
Just recently I got a code (0407) and thought since I just replaced the sensor less than a year (20k) ago. So I go under and see what was going on there, and to my surprise I see that the harness to the CPS (ref) is mangled and chewed up by the acc.belt. It's only about 12" long and connects to the CPS, and has another larger connector on the other side behind the oil fitler.
So after searching for it online for a while, as it's only about a ft in length, but come to a conclusion that it's sold with the "main ECU harness".
Has anyone ever had similar experiences?
since I just replaced the sensor less than a year (20k) ago. So I go under and see what was going on there, and to my surprise I see that the harness to the CPS (ref) is mangled and chewed up by the acc.belt. It's only about 12" long and connects to the CPS, and has another larger connector on the other side behind the oil fitler. So after searching for it online for a while, as it's only about a ft in length, but come to a conclusion that it's sold with the "main ECU harness".
Has anyone ever had similar experiences?
.. Car starts as fast as my 2003 now 
... Thanks to those who helped ...
's 
Thread
Thread Starter
Forum
Replies
Last Post
My Coffee
New Member Introductions
15
Jun 6, 2017 02:01 PM
Kyle Lee Cleveland
6th Generation Maxima (2004-2008)
3
Sep 28, 2015 07:58 AM