Maxima Forums
front1
front1
0 2014/10/20 13:51:51
taking several measurements of the hubs that are usually not great quality... the reason that Nissan requires the rotors be turned on the vehicle is because of bearing run-out... the best way to beat this is to lathe the hub on a brake lathe, then marry to the rotor and turn the rotor... lastly mark your hub stud with a rotor stud hole and NEVER move it from that place until you need a new set of rotors on the car... then you'll only need to cut the rotors :)))
taking several measurements of the hubs that are usually not great quality... the reason that Nissan requires the rotors be turned on the vehicle is because of bearing run-out... the best way to beat this is to lathe the hub on a brake lathe, then marry to the rotor and turn the rotor... lastly mark your hub stud with a rotor stud hole and NEVER move it from that place until you need a new set of rotors on the car... then you'll only need to cut the rotors :)))
0 2014/02/06 22:56:09
image 3464570672
image 3464570672
0 2014/02/06 22:15:12
OEM bushing candle!!!
OEM bushing candle!!!
0 2014/02/06 22:00:07
no press, no problem. Torch the sleeve, push out with a flathead screwdriver, torch the rubber a little, sawzaw the next sleeve on the inside in two places about 1/2 apart, pound back with a flathead & it will tap right out.
no press, no problem. Torch the sleeve, push out with a flathead screwdriver, torch the rubber a little, sawzaw the next sleeve on the inside in two places about 1/2 apart, pound back with a flathead & it will tap right out.
0 2014/02/04 10:52:51
new powdercoat and rebuilt the AP racing CP5200 calipers. new hawk pads
new powdercoat and rebuilt the AP racing CP5200 calipers. new hawk pads
0 2014/02/04 10:46:40
NO BUENO!!
NO BUENO!!
0 2014/01/10 12:17:04
two sets of rotors :)... Calipers will have the 'now powder coated over' emblem removed & a custom generation correct aluminum NISMO badge created and welded into place... ya, it was an afterthought, lol!!
two sets of rotors :)... Calipers will have the 'now powder coated over' emblem removed & a custom generation correct aluminum NISMO badge created and welded into place... ya, it was an afterthought, lol!!
0 2014/01/10 12:07:03
buying the AP sleeve today from STILLEN... Kenny is in the sports car division & always takes care of my complicated questions and orders!!
buying the AP sleeve today from STILLEN... Kenny is in the sports car division & always takes care of my complicated questions and orders!!
0 2014/01/10 11:58:58
removed the LIM baffles for more air to support the .20 over bore... then reset the new MAF! Gained power and mpg ;))
removed the LIM baffles for more air to support the .20 over bore... then reset the new MAF! Gained power and mpg ;))
0 2014/01/10 11:55:18
image 1821714476
image 1821714476
0 2013/12/22 18:13:32
image 4196643603
image 4196643603
0 2013/12/22 18:12:43
image 2417814374
image 2417814374
0 2013/12/19 11:05:27
image 2054073163
image 2054073163
0 2013/12/19 09:31:53
image 252832058
image 252832058
0 2013/12/03 23:26:04
image 2989408756
image 2989408756
0 2013/12/03 23:17:42
separated & re-bonded with polyurethane adhesive from EVERCOAT!!
separated & re-bonded with polyurethane adhesive from EVERCOAT!!
0 2013/11/08 09:50:07
image 1611242253
image 1611242253
0 2013/08/14 00:53:32
image 3478577874
image 3478577874
0 2013/06/25 22:41:17
image 621456332
image 621456332
0 2013/06/25 22:40:31
bored 20 over... NA motor
bored 20 over... NA motor
0 2013/06/25 22:39:48
image 3453504787
image 3453504787
0 2013/06/25 22:39:17
new chains dialed in
new chains dialed in
0 2013/06/25 22:37:21
new chains
new chains
0 2013/06/25 22:36:59
image 1280754994
image 1280754994
0 2013/06/23 02:41:04
I love my NA
I love my NA
0 2013/06/22 09:22:09
getting the VQ30 back in where she belongs.
getting the VQ30 back in where she belongs.
0 2013/06/22 09:21:24
image 4174249165
image 4174249165
0 2013/06/22 09:20:17
you aren't able to buy this gasket... so you must make it
you aren't able to buy this gasket... so you must make it
0 2013/06/13 09:45:59
image 2867156347
image 2867156347
0 2013/06/13 09:42:33
BORED 20 OVER WITH NEW PISTONS AND RINGS
BORED 20 OVER WITH NEW PISTONS AND RINGS
0 2013/06/13 09:38:19
image 3939839654
image 3939839654
0 2013/06/07 00:20:31
headed to the machine shop for the workings and a good cylinder BORE!!!!
headed to the machine shop for the workings and a good cylinder BORE!!!!
0 2013/06/07 00:20:02
image 2932345750
image 2932345750
0 2013/06/02 20:47:54
image 3987493168
image 3987493168
0 2013/06/02 20:47:26
moulded lip kit
moulded lip kit
0 2011/10/04 20:39:21
skirts sanded down to the poly, shot with flexible primer, wetsnaded with 400, shot with fresh PPG DCC9300 Black!
skirts sanded down to the poly, shot with flexible primer, wetsnaded with 400, shot with fresh PPG DCC9300 Black!
0 2011/10/04 20:35:50
mmmmm...yummy! Fresh PPG on my moulded Stillen kit. I first moulded the Stillen Poly Kit into the bumpers(both front and rear), then fixed the nicks and scratches, and laid down some fresh paint...all in the comfort of home :)
mmmmm...yummy! Fresh PPG on my moulded Stillen kit. I first moulded the Stillen Poly Kit into the bumpers(both front and rear), then fixed the nicks and scratches, and laid down some fresh paint...all in the comfort of home :)
4 2011/10/02 02:30:56
Mount Hood on my two week road trip!
Mount Hood on my two week road trip!
2 2009/10/06 22:13:00
yay for custom badges :-)
yay for custom badges :-)
0 2009/05/20 00:25:12