No Red valve covers here, MrGone :)
#3
That was just high temp rattle can.... I had to replace the valve cover gaskets, so I decided to paint the covers while they were off...
Damn...picked up on the K&N just by the sticker, huh? As far as performance, the only thing I've really done was the full WSP exhaust. Right now I am using the stock b-pipe and muffler, eventually I'll put the wsp/magnaflow back on. Honestly, I have no ambitions to try to make a 'race car', if I were going to do that, I'd start with something RWD....
But yes, I have done a ton of work to this car - just about everything except get internal on the engine.
Damn...picked up on the K&N just by the sticker, huh? As far as performance, the only thing I've really done was the full WSP exhaust. Right now I am using the stock b-pipe and muffler, eventually I'll put the wsp/magnaflow back on. Honestly, I have no ambitions to try to make a 'race car', if I were going to do that, I'd start with something RWD....
But yes, I have done a ton of work to this car - just about everything except get internal on the engine.
#4
Originally Posted by 90pearlSE
That was just high temp rattle can.... I had to replace the valve cover gaskets, so I decided to paint the covers while they were off...
Damn...picked up on the K&N just by the sticker, huh? As far as performance, the only thing I've really done was the full WSP exhaust. Right now I am using the stock b-pipe and muffler, eventually I'll put the wsp/magnaflow back on. Honestly, I have no ambitions to try to make a 'race car', if I were going to do that, I'd start with something RWD....
But yes, I have done a ton of work to this car - just about everything except get internal on the engine.
Damn...picked up on the K&N just by the sticker, huh? As far as performance, the only thing I've really done was the full WSP exhaust. Right now I am using the stock b-pipe and muffler, eventually I'll put the wsp/magnaflow back on. Honestly, I have no ambitions to try to make a 'race car', if I were going to do that, I'd start with something RWD....
But yes, I have done a ton of work to this car - just about everything except get internal on the engine.
bah, no need to make it a race car, just enjoy it as is
but flush your brake and clutch fluid
#5
Everything was flushed and cleaned when I did the whole car/tranny swap....maybe just the angle or flash when I took the pic.
Here's a link to my posts on the NissanX boards when I was building this car...
http://www.nissanx.com/f0rums/thread...1bdc3105ae9609
Here's a link to my posts on the NissanX boards when I was building this car...
http://www.nissanx.com/f0rums/thread...1bdc3105ae9609
#8
not bad and yes, it the intake manifold has to come off to remove the front valve cover.
if I get a PM that doesn't directly lead to me getting money in my paypal I will ban
if I get a PM that doesn't directly lead to me getting money in my paypal I will ban
#11
Originally Posted by DanNY
no red cover here either
but I thought it was just going to be the valve cover only pic... where they aren't on the car
#16
Originally Posted by 4dscPat
amazing, my only complaint is the rather large dirty corroded throttle cable thinger on the throttle body. Chroming that would be the final touch for perfection.
next thing i'll hear you say is that my tranny case is too dull
unless you have done it yourself then you can't really critize about the work right?
Thread
Thread Starter
Forum
Replies
Last Post
tseng1023
5th Generation Classifieds (2000-2003)
3
10-15-2015 08:30 AM