Bank 1 Sensor 2 - will this fit
#1
Bank 1 Sensor 2 - will this fit
It says it fits my year but I get so confused trying to figure which O2 sensor is which
http://www.ebay.com/itm/NEW-DIRECT-F...ht_3787wt_1304
http://www.ebay.com/itm/NEW-DIRECT-F...ht_3787wt_1304
#5
#7
search front heated oxygen sensor. go to rock auto and get a decent one. Its kinda importante. As far as interchangeability the up stream is diff from the downstream. Here http://www.rockauto.com/catalog/rafr...k41135-2678608 get the airtex ones IIRC they are like $34. whole bunch of wholesale prices right now so load up
#9
so something like these??
http://www.ebay.com/itm/New-O2-Oxyge...ht_2439wt_1304
http://www.ebay.com/itm/O2-Oxygen-Se...ht_2319wt_1139
http://www.ebay.com/itm/New-O2-Oxyge...ht_2439wt_1304
http://www.ebay.com/itm/O2-Oxygen-Se...ht_2319wt_1139
#10
#11
OK, Mike, you need to change the DOWNSTREAM one right? IIRC Bank 1 sensor 2 is downstream. This would be the one by the cat. Here is a link for down stream... 4 wires http://www.ebay.com/itm/NEW-DIRECT-F...76df41&vxp=mtr
Upstream has 3 wires and those 2 I believe are interchangeable with each other.
Upstream has 3 wires and those 2 I believe are interchangeable with each other.
#13
Per http://www.courtesyparts.com/kb_sear...utton=Go&cat=1
Bank 1 Sensor 1, located on exhaust tube near firewall
Bank 2 Sensor 1, located on manifold near radiator
Which would leave Bank 1 Sensor 2 located pre cat (Under the car)
Don't know if this has helped at all or just confused. I'd just search UPSTREAM and DOWNSTREAM on ebay. So NO, the one you posted in your 1st post will NOT fit DOWNSTREAM.
Bank 1 Sensor 1, located on exhaust tube near firewall
Bank 2 Sensor 1, located on manifold near radiator
Which would leave Bank 1 Sensor 2 located pre cat (Under the car)
Don't know if this has helped at all or just confused. I'd just search UPSTREAM and DOWNSTREAM on ebay. So NO, the one you posted in your 1st post will NOT fit DOWNSTREAM.
Last edited by 2brosgixxer; 03-27-2012 at 11:38 PM.
#14
Per http://www.courtesyparts.com/kb_sear...utton=Go&cat=1
Bank 1 Sensor 1, located on exhaust tube near firewall
Bank 2 Sensor 1, located on manifold near radiator
Which would leave Bank 1 Sensor 2 located pre cat (Under the car)
Don't know if this has helped at all or just confused. I'd just search UPSTREAM and DOWNSTREAM on ebay. So NO, the one you posted in your 1st post will NOT fit DOWNSTREAM.
Bank 1 Sensor 1, located on exhaust tube near firewall
Bank 2 Sensor 1, located on manifold near radiator
Which would leave Bank 1 Sensor 2 located pre cat (Under the car)
Don't know if this has helped at all or just confused. I'd just search UPSTREAM and DOWNSTREAM on ebay. So NO, the one you posted in your 1st post will NOT fit DOWNSTREAM.
#15
You're close - Sensor 2 is always "post" (after) cat. Fed spec cars have one post cat sensor, identified as Bank1 Sensor 2; Cali specs have two post cat sensors. In our Maximas, Bank 1 is the cylinder bank at the rear of the engine compartment; Bank 2 is at the front of the engine compartment.
FED SPEC :
Bank 1 Sensor 1 = Firewall side on the Y pipe reachable under the car ( but still UPSTREAM
Bank 2 Sensor 1 = Front Engine just below engine mount on the Y pipe Upstream as well
Bank 1 Sensor 2 = POST cat downstream after all the emission crap on the stock pipe.
Upstream sensors are interchangable with each other. Downstream will NOT work anywhere else but Downstream.
Last edited by Phromethius; 03-28-2012 at 08:23 AM.
#17
Partially yes, but you left out the most important qualifier, The banks shows the physical location, the SENSOR NUMBER tells you whether it is up stream or downstream.
FED SPEC :
Bank 1 Sensor 1 = Firewall side on the Y pipe reachable under the car ( but still UPSTREAM
Bank 2 Sensor 1 = Front Engine just below engine mount on the Y pipe Upstream as well
Bank 1 Sensor 2 = POST cat downstream after all the emission crap on the stock pipe.
Upstream sensors are interchangable with each other. Downstream will NOT work anywhere else but Downstream.
FED SPEC :
Bank 1 Sensor 1 = Firewall side on the Y pipe reachable under the car ( but still UPSTREAM
Bank 2 Sensor 1 = Front Engine just below engine mount on the Y pipe Upstream as well
Bank 1 Sensor 2 = POST cat downstream after all the emission crap on the stock pipe.
Upstream sensors are interchangable with each other. Downstream will NOT work anywhere else but Downstream.
#19
I have finally found a diagram that makes sense to me, and I thought that I would post it for all to see. This website allows you to input your specific vin# and receive detailed diagrams of the parts "http://www.nissanpartszone.com".
Last edited by Stoneyburt; 03-29-2012 at 03:02 PM. Reason: update photo
#20
Our engine is a V shape guys. 2 different banks. Every direction in a car is given as if you are on the drivers side. So left is always radiator side and right is always firewall side. Just call and ask the company you are ordering from if you have questions its not embarrassing to not know something and a whole lot better than ordering the wrong part anyways
#22
Nice. This applies only to a CALI spec Max since it has 4 O2 sensors, right?
#23
@Wizard (By the way bad *** tail lights man..)
This diagram shows both Federal and Cali specs. From what I understand
Federal:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
as Phromethius stated "Bank 1 Sensor 2 = POST cat downstream after all the emission crap on the stock pipe."
Cali:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 2 sensor 2
Bank 1 sensor 2
In that order according to the diagram (LH, RH).
@dwapenyi
And now my head is hurting again and has been since 2005, but I believe this is how it goes and I agree with ShocknAwe I am going to call rock auto before I order this Bank 1 sensor 2 (H02S12) and ask to make sure.
This diagram shows both Federal and Cali specs. From what I understand
Federal:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
as Phromethius stated "Bank 1 Sensor 2 = POST cat downstream after all the emission crap on the stock pipe."
Cali:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 2 sensor 2
Bank 1 sensor 2
In that order according to the diagram (LH, RH).
@dwapenyi
And now my head is hurting again and has been since 2005, but I believe this is how it goes and I agree with ShocknAwe I am going to call rock auto before I order this Bank 1 sensor 2 (H02S12) and ask to make sure.
#24
Picture is wrong as far as labeling the banks for the upstream (before the cat) sensors. Bank one is always the bank with cylinder #1; in our vehicles cylinders #1, 3 and 5 are in the REAR bank next to the firewall.
#25
^ thats right. on my car, the vq30de engine. the odd number cylinders(1,3,5) are closest to the firewall and thats bank 1. The even numbered cylinder(2,4,6) are closest to the radiator and that is bank 2. I misspoke earlier about the banks when I said the radiator side is bank 1 and firewall is bank 2. This should clear it up but nissan calls both front heated oxygen sensors and they will fit both. The only different ones are the post cat and those WILL NOT fit on the y-pipe locations. Or if you are a visual learner:
and this is the fed spec:
so as you can see the 02 near the cat is also bank 1 which is a bit strange but it is what it is. Again Nissan calls them front and rear heated oxygen sensors and uses the right(firewall) or left(radiator) directions but I believe all of the 02 sensors the cali and fed spec share are the same wire color and the cali spec cars just have other sensors with other color wire. Hope this helps.
and this is the fed spec:
so as you can see the 02 near the cat is also bank 1 which is a bit strange but it is what it is. Again Nissan calls them front and rear heated oxygen sensors and uses the right(firewall) or left(radiator) directions but I believe all of the 02 sensors the cali and fed spec share are the same wire color and the cali spec cars just have other sensors with other color wire. Hope this helps.
Last edited by ShocknAwe; 04-02-2012 at 12:23 PM.
#26
I think your right about my labels:
Bank 1 sensor 1
Bank 2 sensor 1
I have a 1999 SE (Federal 3 sensors) Can we agree that for my vehicle
Bank 1 sensor 2 is labeled correctly in my diagram and in Shocknawe's diagram the label is:
H02S2-B1
Rear O2
sensor B1
(White)
The part # we should look for is
226A0-0SL710?
I want to order one for my car but I do not want to get the wrong one or have a parts guy insist on the wrong one.
#27
ShocknAwes diagrams are correct for everything, so I would just use that instead.
Fed and Cali Spec cars have the same banks. The difference is that the Cali spec car has more O2 sensors.
DW
#28
Bank 1 sensor 1, should be a 3 wire 02(2 white, one black, closest to firewall). On the actual sensor itself has 3 holes drilled down the sensor. And that sensor will have more wire than the rest. Also do NOT drop the sensors, I read that a foot or more fall can cause the sensor not to work. If u r FED spec u only got 3 sensors, one near the firewall of the y, one closer to the rad, and one after the cat converter(4 way).
#29
Yeah sorry to confuse guys, my run down applied ONLY to FED spec. I just redid all my sensors, did like three months of research before hand on such a simple job. Thats why I know about the FED spec. my summary is correct for Federal maxs and SHocks diagram for CALIFORNIA spec is correct for Cali maxs
#30
Per http://www.courtesyparts.com/kb_sear...utton=Go&cat=1
Bank 1 Sensor 1, located on exhaust tube near firewall
Bank 2 Sensor 1, located on manifold near radiator
Which would leave Bank 1 Sensor 2 located pre cat (Under the car)
Don't know if this has helped at all or just confused. I'd just search UPSTREAM and DOWNSTREAM on ebay. So NO, the one you posted in your 1st post will NOT fit DOWNSTREAM.
Bank 1 Sensor 1, located on exhaust tube near firewall
Bank 2 Sensor 1, located on manifold near radiator
Which would leave Bank 1 Sensor 2 located pre cat (Under the car)
Don't know if this has helped at all or just confused. I'd just search UPSTREAM and DOWNSTREAM on ebay. So NO, the one you posted in your 1st post will NOT fit DOWNSTREAM.
#31
front O2 sensors as identical with the same part# 234-3098
Amazon is selling them for $43.94 each with free shipping!!
http://www.amazon.com/Denso-234-3098...3567364&sr=8-1
So the question is, are the front sensors identical, interchangeable?
#32
Denso sells great O2 sensors at a great price and their website lists both the
front O2 sensors as identical with the same part# 234-3098
Amazon is selling them for $43.94 each with free shipping!!
http://www.amazon.com/Denso-234-3098...3567364&sr=8-1
So the question is, are the front sensors identical, interchangeable?
front O2 sensors as identical with the same part# 234-3098
Amazon is selling them for $43.94 each with free shipping!!
http://www.amazon.com/Denso-234-3098...3567364&sr=8-1
So the question is, are the front sensors identical, interchangeable?
#33
These sensors are so confusing i spent hours reading about them.I also need oxygen sensor bank 1 sensor 2 for my 1997 Maxima which is downstream sensor and from reading this thread it's 4 wire sensor and Denso is decent brand so i just ordered 1 from ebay but still not 100% sure if i got the right part.Can somebody please confirm this sensor i ordered is in fact bank 1 sensor 2,here is the link http://www.ebay.ca/itm/350824572393?...84.m1497.l2649
Thanks in advance guys.
Thanks in advance guys.
Last edited by Bosancero; 07-10-2013 at 10:49 PM.
#34
These sensors are so confusing i spent hours reading about them.I also need oxygen sensor bank 1 sensor 2 for my 1997 Maxima which is downstream sensor and from reading this thread it's 4 wire sensor and Denso is decent brand so i just ordered 1 from ebay but still not 100% sure if i got the right part.Can somebody please confirm this sensor i ordered is in fact bank 1 sensor 2,here is the link http://www.ebay.ca/itm/350824572393?...84.m1497.l2649
Thanks in advance guys.
Thanks in advance guys.
#35
That's what I was thinking too, luckily this seller labeled it as downstream sensor.Many sellers out there just label them as 3 or 4 wire oxygen sensors. Thank you for your confirmation Phromethius.
#36
I know the 95/96 maximas have the downstream inside the catalytic converter and the sensor is much smaller. I would go under the car to verify that your sensor is inside a pipe and not in the catalytic converter.
#37
BUMP
my car has P0155 02 sensor heater circuit bank 2 sensor 1. Cali Spec 1999.
can anyone point me in the right direction as to which 02 sensor i need ? pm me an ebay link or whatever please
my car has P0155 02 sensor heater circuit bank 2 sensor 1. Cali Spec 1999.
can anyone point me in the right direction as to which 02 sensor i need ? pm me an ebay link or whatever please
#38
#39