oh crap !!!
ouch.....hopefully, you just fried your clutch. How high did the revs go up? emax95 did the exact same thing a little while back and he came out with only a messed up clutch. You could possibly damage the valves if the engine revs that high. That would be major. But, hopefully your clutch just went bad.....good luck man, and keep us posted...
Originally posted by UMD_MaxSE
ouch.....hopefully, you just fried your clutch. How high did the revs go up? emax95 did the exact same thing a little while back and he came out with only a messed up clutch. You could possibly damage the valves if the engine revs that high. That would be major. But, hopefully your clutch just went bad.....good luck man, and keep us posted...
ouch.....hopefully, you just fried your clutch. How high did the revs go up? emax95 did the exact same thing a little while back and he came out with only a messed up clutch. You could possibly damage the valves if the engine revs that high. That would be major. But, hopefully your clutch just went bad.....good luck man, and keep us posted...
Originally posted by ToYLeT902
so ur saying everyone who revs there engine to redline will ruin there valves? or just in this case?
so ur saying everyone who revs there engine to redline will ruin there valves? or just in this case?
Guest
Posts: n/a
update from the dealership ,the timeing chain broke and a couple of valves are bent ,they are going to check to see if i voided the warrenty with my mods but since they have to prove that the mods caused the problem hopefully they'll just fix it under warrenty,if not i wonder if a pathfinder engine swap is possible
Originally posted by QUANSUNG
update from the dealership ,the timeing chain broke and a couple of valves are bent ,they are going to check to see if i voided the warrenty with my mods but since they have to prove that the mods caused the problem hopefully they'll just fix it under warrenty,if not i wonder if a pathfinder engine swap is possible
update from the dealership ,the timeing chain broke and a couple of valves are bent ,they are going to check to see if i voided the warrenty with my mods but since they have to prove that the mods caused the problem hopefully they'll just fix it under warrenty,if not i wonder if a pathfinder engine swap is possible
Thats sucks!
I went into 2nd with my I30 at about 90 MPH, this was acompinied by my SC pumping out about 8 PSI! Luckly for me my Sucky Centerforce Clutch just snaped and it saved my engine and tranny. Good Luck.
I went into 2nd with my I30 at about 90 MPH, this was acompinied by my SC pumping out about 8 PSI! Luckly for me my Sucky Centerforce Clutch just snaped and it saved my engine and tranny. Good Luck.
An engine can rev up to its potential and then it is left up to the parts contained within to determine if the parts can sustain the stress: stock parts can tolerate only so much. After that, if you don't have hi-po parts, you're going to damage something. The Honda folks can upgrade internals to sustain the high RPMs, but Maxima's are limited to the availabity of true hi-po parts to accomplish the same.
A prime example would be a 2000 Chevrolet Monte Carolo versus a 2000 Chevrolet Cup car. The standard factory car can will blow up under extended duress and not have too much power, but an engine of the same with changed internals and built for high RPMs will last much longer with way better gains.
A prime example would be a 2000 Chevrolet Monte Carolo versus a 2000 Chevrolet Cup car. The standard factory car can will blow up under extended duress and not have too much power, but an engine of the same with changed internals and built for high RPMs will last much longer with way better gains.
Thread
Thread Starter
Forum
Replies
Last Post
londonflu
3rd Generation Maxima (1989-1994)
40
Sep 25, 2015 09:11 AM
JoshG
4th Generation Maxima (1995-1999)
51
Sep 21, 2015 10:41 PM
raffivegas
6th Generation Classifieds (2004-2008)
0
Aug 23, 2015 09:54 PM





