Completing My Exhaust
10-16-2007, 05:17 PM
#1
Senior Member
Thread Starter
iTrader: (10)
Join Date: May 2007
Location: Colliers, NL Canada
Posts: 476
Completing My Exhaust
Hey Guys,
I currently have a Warpspeed Y (No Headers), and have a Y-Pipe Back Exhaust ready to go on. (2.5")
I have a Magnaflow Cat, Resonator, & Dual tip muffler, and some stainless tips.
I need a B-pipe, and an extension to reach the muffler. Does anyone know where I can find this? I was going to get a custom-job done, but the time spent trying to mandrel-bend all of that pipe around the back axle would really be a pain.
I'd like to get a B-pipe and rear section (2.5"), which would make life a LOT less complicated. The muffler is a center in / dual out compared to the stock side in / dual out that I will be replacing.
Does anyone have any advice for finding a good SS B and rear section???
I currently have a Warpspeed Y (No Headers), and have a Y-Pipe Back Exhaust ready to go on. (2.5")
I have a Magnaflow Cat, Resonator, & Dual tip muffler, and some stainless tips.
I need a B-pipe, and an extension to reach the muffler. Does anyone know where I can find this? I was going to get a custom-job done, but the time spent trying to mandrel-bend all of that pipe around the back axle would really be a pain.
I'd like to get a B-pipe and rear section (2.5"), which would make life a LOT less complicated. The muffler is a center in / dual out compared to the stock side in / dual out that I will be replacing.
Does anyone have any advice for finding a good SS B and rear section???
10-17-2007, 03:22 PM
#2
Hey Guys,
I currently have a Warpspeed Y (No Headers), and have a Y-Pipe Back Exhaust ready to go on. (2.5")
I have a Magnaflow Cat, Resonator, & Dual tip muffler, and some stainless tips.
I need a B-pipe, and an extension to reach the muffler. Does anyone know where I can find this? I was going to get a custom-job done, but the time spent trying to mandrel-bend all of that pipe around the back axle would really be a pain.
I'd like to get a B-pipe and rear section (2.5"), which would make life a LOT less complicated. The muffler is a center in / dual out compared to the stock side in / dual out that I will be replacing.
Does anyone have any advice for finding a good SS B and rear section???
I currently have a Warpspeed Y (No Headers), and have a Y-Pipe Back Exhaust ready to go on. (2.5")
I have a Magnaflow Cat, Resonator, & Dual tip muffler, and some stainless tips.
I need a B-pipe, and an extension to reach the muffler. Does anyone know where I can find this? I was going to get a custom-job done, but the time spent trying to mandrel-bend all of that pipe around the back axle would really be a pain.
I'd like to get a B-pipe and rear section (2.5"), which would make life a LOT less complicated. The muffler is a center in / dual out compared to the stock side in / dual out that I will be replacing.
Does anyone have any advice for finding a good SS B and rear section???
If you are in Mass, try Lou's Custom Exhaust. They have a few locations in Mass. http://www.louscustomexhaust.com/locations.html
Great work and good prices!
10-17-2007, 03:38 PM
#5
10-18-2007, 09:47 AM
#6
Where are you located?
If you are in Mass, try Lou's Custom Exhaust. They have a few locations in Mass. http://www.louscustomexhaust.com/locations.html
Great work and good prices!
If you are in Mass, try Lou's Custom Exhaust. They have a few locations in Mass. http://www.louscustomexhaust.com/locations.html
Great work and good prices!
It's not hard at all for a custom shop to make a b-pipe, Lou's did mine from the cat back and remounted the muffler all in under an hour...
10-18-2007, 07:21 PM
#7
Senior Member
Thread Starter
iTrader: (10)
Join Date: May 2007
Location: Colliers, NL Canada
Posts: 476
Under an hour?
It couldn't have been mandrel bent & Butt welded?
I think I'll pay the extra labour to keep the 2.5" right through. Is it worth the extra time & Labour? I was quoted ~ 5 Hours for the complete exhaust fabbed.
It couldn't have been mandrel bent & Butt welded?
I think I'll pay the extra labour to keep the 2.5" right through. Is it worth the extra time & Labour? I was quoted ~ 5 Hours for the complete exhaust fabbed.
10-19-2007, 11:42 AM
#8
They replaced my exhaust in no time at all!
Thread
Thread Starter
Forum
Replies
Last Post
James92SE
3rd Generation Maxima (1989-1994)
142
01-02-2024 09:23 AM
My Coffee
New Member Introductions
15
06-06-2017 02:01 PM
KabirUTA13
5th Generation Classifieds (2000-2003)
19
10-17-2015 02:15 AM