What is this "cutoff mod" you speak of?



You do realize that his motor/turbo set up is worth your entire car, right?

 

stop b1tching and get x9s.

 

17x8 xxr 522 (gold) - $600)

 

From what I remember him bragging on:

- Twin-loop fail muffler
- Rev-up Cams (Still don't understand this one without the supporting mods)
- NWP block plate
- NWP intake spacers (don't remember if he has the whole kit or jus the LIM spacer)
- Cheap short-ram intake
- Port and polished UIM

I don't know if there was anything else. Do I believe him? Not really. I'd guess that he has half of this stuff.

 

Has he contributed anything positive to this forum?

 

Color mod.

Sorreh, Mr. Retrofit.

 

Well, there was that one time that...










Or maybe...














Well...



No, not really.

 

Rev-up cams? yea, no way his car has those. I have rev up cams and they are not easy to install no way in hell clashez installed those.

port and polished UIM? Out of all the stupid and pointless mods i have heard, somebody ported and polished the UIM?

 

no. It was funny at first the twin loop BS, then i had fun arguing with rochester over him. now its just like nothing he even says is logical.

 

I think this is the incidence that will make me finally put the clown on the ignore list. Trying to put down what's probably the best done up 4th gen on this forum and say his turd mobile is better. It's too bad his stories about trade offers aren't true because it would right the universe if he traded that thing for a Honda from one of his local riceboys.

 

JIC Chrome Rims CHEAP - $300

 

The ONLY reason I'd port and polish the UIM on my G35 is if I had the intent of gasket-matching it. Which I actually do, eventually. After I buy a Motordyne spacer, of course.

I'm trying to find ways to resolve the air starvation issues in the front two cylinders. The IM on the RWD VQ platforms is great and terrible at the same time.

 

Of course..



I honestly wouldn't touch them. More color = less beam intensity. The MH1's aren't super intense to begin with and have decent color.

 

This.

No, which is why in my opinion he should have been banned a long time ago. His posts are a waste of bandwidth.

 

i see Clashez logged in under his alter ego name now

 

Oh, I know. I did my reading.

I just want a bit crisper of a cutoff. Unless the stock beam cutoff is that sharp?

 

It needs to be more than just a SN ban. They need to do a name AND IP ban on him.

He just needs to go back to the Honda forum where he belongs...

 

Nahhh.

No reason, 255s can go on there if things really get out of hand and that to me is too much tire for a Maxima.

245-40-17 is more than enough for me to bawss around corners.

If I need more than that then I need suspension work done.

 

aackshum pm me price+pay info for that shifter trim and a good vent assembly i broke one of the fins yesterday when i dropped it

 

 

Fck those look good and they're cheap.

And they're not thaaat heavy.

If those are for sale when I have to drive back from ATL i'll pick em up for 's

 

If you want sharpness, you want less color. They're sharp enough though.
http://www.theretrofitsource.com/ima...mh1mazda6l.jpg

 

Chrisman had me get these for the 4th gen and they do look prety good even if i did install(hack) them

Bi-xenon: Morimoto Mini H1 4.1

 

 

K 54,000 now i haz to go to class.

 

Dually noted.

I'm getting the same minis, except I'm planning on getting the D2S's instead of the H1's.

 

Should'nt there be a jar of peach marmalade in that hand?

 

 

haha everytime i point Clashez and his alter ego name out he loggs both of them off

 

Dont check yo thread.

 

I'm also trying to figure out what shrouds I want. I'm leaning toward the Gatling or the Apollo for the G...

 

just a little tip im sure chrisman has a better method but when cutting the bottom of the shroud to fit the contour use a template and trace it on the shroud i ended up having to get a extra set

 

Laughs...

 

aackshun!!!! Are you going to use 6MT ECU for your swap?

 

D2S' low beams don't perform as well as the H1's but have better high beam. I believe you can slide the shield down a millimeter or two to expose some more light for the low beam but not 100% sure. I also believe the D2S' are sharper than the H1's.

I wouldn't go with the Apollo's. They're a bit too "rugged" for the sleek G35 coupe headlights. I'd honestly go with full size Gatling Gun shrouds (not the V2's).

Whatchootalkinbout?

 

the shrouds were a bit long and needed trimming to fit the contour of the oe reflector.i must of dun summin really wron if trimming wasnt needed

 

Yes, you sellin? Cause I'm buyin'

 

Which shrouds did you go with? I don't remember. If they were the standard mini Gatling Gun shrouds, you shouldn't have had to trim anything.

 

That was actually kinda funny, peep da reply.

 

Well, I don't plan on using the bi-xenon capability of them. I just want a set of projectors that fit easily into the G housings and have a clean, crisp look to them, so I may just lower the shroud a little if that's the case.

If I go with the Gatling, I was definitely looking at the full versions. I might see about wiring some LED's into my parking lights so that I can light up the vents around the edge as well.