Battery went dead, now it won't start
05-20-2020, 10:31 AM
#41
Newbie - Just Registered
Join Date: May 2020
Posts: 2
What if your security light isn't lighting up at all
[QUOTE=Gemner;8868932]you can read the codes out without a code reader
1) Sit in the driver's seat.
2) Turn the ignition key to the ON position and wait three seconds. (Do not start the car.)
3) Rapidly depress and release the accelerator pedal 5 times in less than 3 seconds.
4) Wait 7 seconds. Push the pedal all the way down for ten seconds until the SES light flashes.
5) Release the pedal and start counting flashes to obtain the four-digit trouble code.
The SES light either flashes quickly or slowly, 10 slow blinks basically means prepare to read the code, then it will blink quickly to read out the first number of the code, pause, then begin blinking quickly to read out the next number (this happens up to 4 times), 10 quick blinks is a 0.
What if your red security light doesn't light up at all my windows won't roll up and down and it talks a lot doesn't work it'll crank but not start
1) Sit in the driver's seat.
2) Turn the ignition key to the ON position and wait three seconds. (Do not start the car.)
3) Rapidly depress and release the accelerator pedal 5 times in less than 3 seconds.
4) Wait 7 seconds. Push the pedal all the way down for ten seconds until the SES light flashes.
5) Release the pedal and start counting flashes to obtain the four-digit trouble code.
The SES light either flashes quickly or slowly, 10 slow blinks basically means prepare to read the code, then it will blink quickly to read out the first number of the code, pause, then begin blinking quickly to read out the next number (this happens up to 4 times), 10 quick blinks is a 0.
What if your red security light doesn't light up at all my windows won't roll up and down and it talks a lot doesn't work it'll crank but not start
05-20-2020, 10:32 AM
#42
Newbie - Just Registered
Join Date: May 2020
Posts: 2
What if your security light isn't lighting up at all
[QUOTE=Gemner;8868932]you can read the codes out without a code reader
1) Sit in the driver's seat.
2) Turn the ignition key to the ON position and wait three seconds. (Do not start the car.)
3) Rapidly depress and release the accelerator pedal 5 times in less than 3 seconds.
4) Wait 7 seconds. Push the pedal all the way down for ten seconds until the SES light flashes.
5) Release the pedal and start counting flashes to obtain the four-digit trouble code.
The SES light either flashes quickly or slowly, 10 slow blinks basically means prepare to read the code, then it will blink quickly to read out the first number of the code, pause, then begin blinking quickly to read out the next number (this happens up to 4 times), 10 quick blinks is a 0.
What if your red security light doesn't light up at all my windows won't roll up and down and it talks a lot doesn't work it'll crank but not start
1) Sit in the driver's seat.
2) Turn the ignition key to the ON position and wait three seconds. (Do not start the car.)
3) Rapidly depress and release the accelerator pedal 5 times in less than 3 seconds.
4) Wait 7 seconds. Push the pedal all the way down for ten seconds until the SES light flashes.
5) Release the pedal and start counting flashes to obtain the four-digit trouble code.
The SES light either flashes quickly or slowly, 10 slow blinks basically means prepare to read the code, then it will blink quickly to read out the first number of the code, pause, then begin blinking quickly to read out the next number (this happens up to 4 times), 10 quick blinks is a 0.
What if your red security light doesn't light up at all my windows won't roll up and down and it talks a lot doesn't work it'll crank but not start
Thread
Thread Starter
Forum
Replies
Last Post
markevans999
3rd Generation Maxima (1989-1994)
7
09-10-2015 04:29 PM
JoshG
4th Generation Maxima (1995-1999)
17
09-05-2015 10:10 PM
trungg86
4th Generation Maxima (1995-1999)
7
09-04-2015 04:58 AM