OMFG!!!!!!!!........I just installed my Fujita cold air intake.......what an awsome piece!!!.if any of you have thought about getting a cold air intake i would really look into this one......nice and easy to install, great hardwear, and sound scary at about 4300 RPM.


Keep Krusin,
Chef

 

Wow nice sig. pics i love the rims and the lip on the rear ones!

 

Thanks Frost!!!

 

Post some pics of your new CAI

 

is it loud? would like to install on wife's car. anxious

 

i have it, just have to install it...

 

I just checked the tracking # and mine will be here on Tuesday. I can't wait to put it on and floor it.

 

what made ya'll go get it? lol.... welcome to the fujita intake club my man..

 

YOU!! Im ordering one Wednesday as well. 13whp

 

YEah make sure you guys are getting the group deal for it.. It is located on the other .org site. Goto Group Deals there for more info.. LAter..

 

i recently installed mine as well, i will get a video of it soon

 

What other site do you mean??

 

Id like to see/hear that when you do.

 

Hey Chef where did you get the fujita from? I will have to come over and here that thing to see if it is something that I need to have.

 

the best place to get it is over at http://www.6thgenmaxima.org then go to group buy.

 

Tek has a clip of it on his car. Its on one of the other forums.

 

here is a short version assuming you know what the car sounds like stock:

http://www.6thgenmaxima.org/videos/fujitacai.wmv

 

Awesome sound and a great gain, but I thought the 6thGen baseline dyno'd a tad higher.

Damn that sound was impressive. Just plain "WOW".

 

I would have thought the same, but almost stock people are getting close numbers to that 200 whp, with striaght pipe and intake RH did 212hp 224tq, so its right on I think..

around 200whp is what we do, sounds low..

by the way thanx for the comment..

 

I couldn't keep the smile in...that sounded GREAT!!

 

The TQ dropped? Have you got a screen snapshot?

 

it dropped only one on that run. it didn't drop any on another run, but it wasn't fully smoothed out..

my best completly smoothed out was 212hp 221tq:

 

If you do the calculation, the 212WHP is close to the 265CHP, but the 224WTQ is much higher that the 255CTQ. I have all 3 cats, Magnaflow resonator, stock mufflers, w/ new piping same diameter as stock (no crimps).

 

OK - I just saw the dyno over on the 6thGen site. The sound alone still gives me a stiffy.

 

yea it deffinatly sounds cool passing people while it roars!!

 

I'm not sure how the calculations are, but 265 minus 24.5% is 200 right..

now 280 minus 24.5% is 211, I'm thinking we are at 280 crank, but I'm not sure of the right calculations..

with the ecu we are at 295hp at crank with those calculations.. since I'm at 223hp 235tq with the ecu..

 

Wow that thing sounds sick. Where can I get one?

 

I think it's more like 20%, .8 * 265 or 1.25 * 211. Anyone???

 

Here's a quick video from a few test runs from inside:

http://www.6thgenmaxima.org/videos/fujitamaxima.wmv

 

Is this intake better than the Injen CAI?


Which sounds louder or meaner at 4000 RPM +?

 

no clue...

 

I like the chirp of the tire at the stop roll lol.... you need a ecu!!!!

 

WOW cant wait to get that joint.

 

mother of god!!! makes me wanna get a 6th gen!! awesome intake

 

Nice!! Like that video too.. Man Fujita needs to start paying us.. LOL.. I have decided that i am going to install this bad boy next week... and i will hopefully be able to take a few clips of it too...

 

Here is a pic of my CAI, and Tek, thanks for the words brotha! i had an Injen, nice but it came off 5 minutes after i put it on, for some reason it tripped my check engine light and made the car run like poop, it might have been installer error or maybe it was the wrong part.....either way i absolutly love this fujita piece, sounds stock until you hammer on it and POOF!!!!......it just comes alive.GRRRRRRRRR!!

 

I'm glad to have influenced so many into buying a good product, if I find anymore to recommend you know I will post it up..

welcome to the Fujita club, enjoy..

 

maxchef has the 2 piece cold air intake. Fujita stopped making that and is only selling the 1 piece cold air intake (MA-2816).

 

oh crap, I didn't even notice that...

 

is that good or bad that chef has the 2 piece one? I will call him and let him know if it is bad.