Safc2 wiring question
#1
Senior Member
Thread Starter
iTrader: (5)
Join Date: Apr 2006
Location: Eastern Mississippi
Posts: 780
Safc2 wiring question
Hey guys I'm souped because I just picked up a used safc2 and a walbro. The only problem is is that the wiring harness for the safc is completely hacked. I plan on replacing the wires with thicker gauge wires and I was just wondering if the step down in resistance over whatever distance I need to use would somehow mess up my tuning ability.
Am I just crazy?
DF
Am I just crazy?
DF
#9
Senior Member
Thread Starter
iTrader: (5)
Join Date: Apr 2006
Location: Eastern Mississippi
Posts: 780
I've been looking for pinout diagrams for my car, but I can only find wiring diagrams for an 02 in the All Motor section in the faqs. Can someone either confirm that that pinout is also for my year (2000), or show me where to go so I can get this puppy up and running!
Thanks,
DF
Thanks,
DF
#10
Senior Member
Thread Starter
iTrader: (5)
Join Date: Apr 2006
Location: Eastern Mississippi
Posts: 780
Sorry I just have too many little questions, so I guess I'll throw them all in here too.
1. What should I do about the first turnover once installing a walbro, safc2, and cartech.
2. Do I need an afpr at this point, or will the stock one manage?
3. With h/y/i/cleared out exhaust, what kind of power should I be looking at after a dyno tune?
1. What should I do about the first turnover once installing a walbro, safc2, and cartech.
2. Do I need an afpr at this point, or will the stock one manage?
3. With h/y/i/cleared out exhaust, what kind of power should I be looking at after a dyno tune?
#11
Supporting Maxima.org Member
iTrader: (15)
Join Date: Oct 2003
Location: Indianapolis, IN
Posts: 744
hey i just reponded to your post in the 5th gen forum.
i forget who made this, but i didnt.
(sorry lost the file to the link...)
its a two page .pdf, if it doesnt work i can email it to you
also here is the link i posted in the 5th gen forum
http://forums.maxima.org/showthread.php?t=311779
i forget who made this, but i didnt.
(sorry lost the file to the link...)
its a two page .pdf, if it doesnt work i can email it to you
also here is the link i posted in the 5th gen forum
http://forums.maxima.org/showthread.php?t=311779
Last edited by Ephraim; 04-20-2014 at 01:53 PM.
#14
Senior Member
Thread Starter
iTrader: (5)
Join Date: Apr 2006
Location: Eastern Mississippi
Posts: 780
Just 2 more questions........
1. There's conflicting ways of setting up the 2 grounds, I assume both work and I can take my pick?
2. I guess there's supposed to be a purple wire? I have a safc2 and it has these wires: red, blue, green, yellow, white, gray, black, brown, pink, and orange......in another thread I read that the purple wire was to go to the knock sensor......
Thanks again,
DF
1. There's conflicting ways of setting up the 2 grounds, I assume both work and I can take my pick?
2. I guess there's supposed to be a purple wire? I have a safc2 and it has these wires: red, blue, green, yellow, white, gray, black, brown, pink, and orange......in another thread I read that the purple wire was to go to the knock sensor......
Thanks again,
DF
#15
Senior Member
Thread Starter
iTrader: (5)
Join Date: Apr 2006
Location: Eastern Mississippi
Posts: 780
Safc2 is up and running, but there's one problem. There's something wrong with the MAF wiring. I definetly have the correct wire, but when I turn the car on it slowly stalls out.
I unplugged the maf and it runs just like it does when I also cross the Yellow and White wires (tried it just to make sure).
Am I missing some sort of secret here?
DF
I unplugged the maf and it runs just like it does when I also cross the Yellow and White wires (tried it just to make sure).
Am I missing some sort of secret here?
DF
Thread
Thread Starter
Forum
Replies
Last Post
The Frye
7th Generation Maxima (2009-2015)
6
09-02-2021 11:03 AM