GB:Ksport Big Brake Kit! $1295 Shipped!
#1
GB:Ksport Big Brake Kit! $1295 Shipped!
Ksport Big Brake Kits
Ksport big brake kits provide the ultimate in stopping power for your vehicle. Integrating new brake technology into the design of the kits allows for a kit that highly reduces brake fade and continually cools and refreshes the brake pads surface under braking. These brake systems are designed for easy installation with minimal tools required (in most applications).
The Ksport big brake kit includes:
* 8-Piston Aluminum calipers
* High quality brake pads
* D.O.T. Compliant Stainless steel brake lines
* Machined aluminum hats
* Carbon steel brackets
* 13 inch large ventilated discs
* Ksport SC5 street brake pads (RC1 race pads available for additional cost)
Extreme Lightweight Caliper:
Our extreme lightweight caliper comes in differential bore configuration. It is machined from aircraft quality billet, weighs just over 5lbs. each, and has machined in protection grooves for the bridge tubes. Aluminum pistons, high temperature seals, and stainless steel brake pad wear plates are also standard on each caliper design. The opposed piston caliper design greatly improves pad wear and caliper rigidity over the OEM design. The stainless steel brake lines stop expansion under pressure.
High Performance Rotor:
Most applications utilize the 2-piece floating disc assembly which reduces weight both rotating and unsprung. The floating disc also stops thermal stresses of extreme heat from warping the disc or cupping the braking surface. The unique slot design on the rotor greatly reduces braking noise and expels gas and pad debris faster than conventional slot designs. Every rotor is always heat treated and balanced before shipment for the best possible performance.
Ksport SC5 Street Pads:
These NAOC ceramic pads are designed to give you the optimal braking performance under street and occasional track conditions. Optimal operating temperatures are between 194°F - 1022°F for fast warm up under normal driving conditions. These pads reduce the amount of brake dust by 50% or more when compared to our race pads. The SC5 pads also greatly reduce the amount of noise and wear on the rotor over the race pads.
Ksport RC1 Race Pads:
These carbon metallic race pads are designed to give you the best stopping power possible under extreme track conditions. Optimal operation temperatures are between 480°F - 1472°F so it is not recommended for street use due to high temperature needed for optimal performance. Designed for the racer in mind to reduce brake fade under extreme conditions.
INTRO PRICING! $1295 shipped to 48 U.S States. for ALL NISSAN APPLICATION
Order Here!!
SUMMER SPECIAL! A32/A33 kit shipped to 48 U.S States.
Order Here!!
Application listed here-
http://www.ksportusa.com/asp/brake_kits.asp
I have installed the kit on my 03 Mazda6s two weeks ago and my feedback so far is that the brake definately bites much harder and faster. The brake pedal feel is very possitive (firm feel). Now it takes less foot pressure effort to get the same amount of brake force. The calipers are very light due to full aluminium design (even lighter than the stock caliper)
The brake will clear 17in and up rims (depends on rim spoke, mine was about 2mm too close so i am running with a set of spacer and so far very solid after 6 months)
Last edited by jinsu; 11-07-2007 at 09:43 AM.
#6
Originally Posted by maxximaa
damn, i got a lot to save up...
I also doubt they will fit behind most stock rims... 6th gen brakes don't even fit behind 2000-2001 17's.
Also Jinsu, how do they work with the stock master cylinder?
#12
hmmm... i am not sure where you getting ksport coilover are all defected from. From all the ksport coilover i have sold so far for maxima (not including all other applications) warranty work has been below 10% which is what i consider way above average in after market industry, especially on products such as full coilovers. but for this thread's sake, we should level the coilover debate out of here.
#24
Originally Posted by 4x4Max
Do you know how much the rotors weigh?
#25
hahaha, i don't think i would use a 5lb rotor on my own car... you just can't reduce mass without reducing heat transfer capacity unless you are talking about carbon fiber rotors.... i will get you guys the weight later today.
#31
Originally Posted by maximariceboi
i was considering these last year....im still debating for this bbk, z32 or rotora
1295 is a good deal for these brakes.... but I have a problem buying unknown brand products. 22lbs for these rotors is way too much. Baer Eardispeed weight half of that and are just as big. 2 piece rotors are supposed to be lighter. I took my Blehmco kit off because of the heavy rotors.
#32
Originally Posted by BlackBIRDVQ
To my knowledge Rotora does not make a kit for our cars. Unless you buy one for a 240SX which "should" fit.
1295 is a good deal for these brakes.... but I have a problem buying unknown brand products. 22lbs for these rotors is way too much. Baer Eardispeed weight half of that and are just as big. 2 piece rotors are supposed to be lighter. I took my Blehmco kit off because of the heavy rotors.
1295 is a good deal for these brakes.... but I have a problem buying unknown brand products. 22lbs for these rotors is way too much. Baer Eardispeed weight half of that and are just as big. 2 piece rotors are supposed to be lighter. I took my Blehmco kit off because of the heavy rotors.
#33
Matt was waiting on the fabricator.... I couldn't wait any longer and ditched my brake setup. For the longest time I been trying to get a hold of Matt to see if he has any of his rotors in stock.... but he never replies to my E-mails. Jeff was kind enough to get the brackets and hub rings done for the Cobra rotors. I got a brand new set of Z32 calipers waiting to be set out for powdercoating, and then I will slap on a set of 2 piece Baer rotors under my new wheels I got
#34
Originally Posted by BlackBIRDVQ
To my knowledge Rotora does not make a kit for our cars. Unless you buy one for a 240SX which "should" fit.
1295 is a good deal for these brakes.... but I have a problem buying unknown brand products. 22lbs for these rotors is way too much. Baer Eardispeed weight half of that and are just as big. 2 piece rotors are supposed to be lighter. I took my Blehmco kit off because of the heavy rotors.
1295 is a good deal for these brakes.... but I have a problem buying unknown brand products. 22lbs for these rotors is way too much. Baer Eardispeed weight half of that and are just as big. 2 piece rotors are supposed to be lighter. I took my Blehmco kit off because of the heavy rotors.
please check again =] for a fact they make bbk for the 5th gens and they make the calipers for the 4th gens. if you are interested pm me.
#37
Originally Posted by jinsu
okay, OFFICIAL Weight for the rotors. 18.5lbs per rotor. Just went and weighted them.
We'll see what the situation is after I buy new tires and go from there