Maxima Forums

Supercharged/Turbocharged The increase in air/fuel pressure above atmospheric pressure in the intake system caused by the action of a supercharger or turbocharger attached to an engine.
View Poll Results: Belt alignment problems? Which kit?
V1 kit, alignment problems
1
11.11%
V2 kit, alignment problems
2
22.22%
V1 kit, no problems
3
33.33%
V2 kit, no problems
3
33.33%
Voters: 9. You may not vote on this poll

If you have had belt alignment problems, which kit?

Thread Tools
 
Search this Thread
 
Old 05-07-2003, 09:26 AM
  #1  
Supporting Maxima.org Member
Thread Starter
iTrader: (59)
 
Stephen Max's Avatar
 
Join Date: Jul 2001
Posts: 5,869
If you have had belt alignment problems, which kit?
Just wondering if the belt alignment problems people are having are kit specific or if people are having problems with both kits.
Stephen Max is offline  
Reply
Old 05-07-2003, 09:34 AM
  #2  
Supporting Maxima.org Member
iTrader: (3)
 
[maxi-overdose]'s Avatar
 
Join Date: Apr 2001
Posts: 4,305
V2 here....had belt alignment problem and the belt was running too close to the plate. added washers to push out the blower.

total belts killed : 3, so far.
[maxi-overdose] is offline  
Reply
Old 05-07-2003, 10:05 AM
  #3  
ejj
Donating Maxima.org Member
iTrader: (5)
 
ejj's Avatar
 
Join Date: Aug 2000
Posts: 4,602
V2 kit, no alignment problems yet, although I'm still on the stock pully.
ejj is offline  
Reply
Old 05-07-2003, 12:06 PM
  #4  
Supporting Maxima.org Member
iTrader: (3)
 
[maxi-overdose]'s Avatar
 
Join Date: Apr 2001
Posts: 4,305
smaller pulley = smaller contact area for the belt = higher chance of getting belt alignment problem
[maxi-overdose] is offline  
Reply
Old 05-07-2003, 04:45 PM
  #5  
Senior Member
 
97blackv1's Avatar
 
Join Date: Jul 2002
Posts: 292
took me a while but i had to tweak a few things like extra washers etc...
97blackv1 is offline  
Reply
Old 05-08-2003, 05:23 AM
  #6  
Supporting Maxima.org Member
iTrader: (38)
 
JAY25's Avatar
 
Join Date: Dec 2000
Location: Near Archer High School, Ga
Posts: 6,451
I was missing two bolts when I first installed my V2 so that was my belt problem so that was my fault not Stillens fault. No problem what so ever after I purchased those two bolts to the plate
JAY25 is offline  
Reply
Old 05-08-2003, 02:49 PM
  #7  
RIP '98 Maxima SE
iTrader: (6)
 
BlackCat's Avatar
 
Join Date: Apr 2002
Posts: 4,262
I didn't put my washers in the right places because I didn't know they were there after I separated the blower and the mounting plate.
BlackCat is offline  
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
I need rear camber plates.
matts95max
General Maxima Discussion
14
05-20-2024 01:16 AM
timing belt replacement
markevans999
3rd Generation Maxima (1989-1994)
8
10-25-2015 08:27 AM
Front End Vibration
alahjahwan09
5th Generation Maxima (2000-2003)
18
09-21-2015 09:12 PM
What is purpose of that small dot at middle of rear brake pads?
bbsitum
4th Generation Maxima (1995-1999)
4
09-11-2015 04:55 PM
Back to Subforum
Supercharged/Turbocharged
View Next Unread
SC off the car in 1.5 hour, not the belt this time.




Advanced Search
Quick Reply: If you have had belt alignment problems, which kit?


Reply Closed Thread Share

All times are GMT -7. The time now is 04:39 PM.