Just installed my turn signal mirrors
#4
Guest
Posts: n/a
Make sure nothing is shorting...
Here is a link to a guide for installing those shells
http://members.***.net/sunten1/LED.doc
Here is a link to a guide for installing those shells
http://members.***.net/sunten1/LED.doc
#5
I wired everything just like the instruction says.All I got in the package was the short wire that came with the mirrors and nothing else do I need to by a harness or a special relay for led bulbs or resistor I don't know.
Thanx
Thanx
#6
Originally Posted by Chickan
check your wiring? check for loose cables? check to see you used the right fuses?
#10
Originally Posted by sunten1
Can you show us a picture of what it came with?
#12
Originally Posted by chenzarino
how did you wire it? Do they work at all or do they blow right away?
Thanx for your help
#13
Had mine for couple months with no problems....How exactly did you get the wires from the back of the mirror to the turn signal? Did you take the mirror off and put the wires through the little hole....I guess the mirror could be pinching the wires causing a short.
#14
Originally Posted by Nick7455
Had mine for couple months with no problems....How exactly did you get the wires from the back of the mirror to the turn signal? Did you take the mirror off and put the wires through the little hole....I guess the mirror could be pinching the wires causing a short.
unless I would have to drill a hole in the original shell.
#16
Originally Posted by Nick7455
No...the way I described is how I did it and there hasn't been a problem....how did you tap into the turn signal...did you try messin with that connection.
#17
The color might be diff on 99....I don't remember green but you might have better luck using wire taps....also what did you use for the ground on the mirror covers? Anytime my fog light fuse has blown it has been because the ground was loose.....maybe there is a little interferance with the ground....Pics would help if you have them of where you grounded it
#18
Originally Posted by Nick7455
The color might be diff on 99....I don't remember green but you might have better luck using wire taps....also what did you use for the ground on the mirror covers? Anytime my fog light fuse has blown it has been because the ground was loose.....maybe there is a little interferance with the ground....Pics would help if you have them of where you grounded it
I've taken the black wire from the LED mirror shells and grounded it to the screw holding the inside door handle on. This seemed like a good place to ground the LED mirror shell.
#22
Originally Posted by dontcrossme
Try a multimeter and make sure you have the ground and the right amount of voltage going to the wire. If your pulling too much ur going to short the fuse. try running a higher awg wire than it suggests.
#23
Originally Posted by maxedout95
I'm running a 16 gauge wire
Maybe try to rewire the extra wire you added to stretch the line to the blinker......not sure what else man..
#24
Originally Posted by Nick7455
Odd....sounds like everything is
Maybe try to rewire the extra wire you added to stretch the line to the blinker......not sure what else man..
Maybe try to rewire the extra wire you added to stretch the line to the blinker......not sure what else man..
I was thinking of running a extra wire from the fuse box to the turn signals but that would be my last option.
ThAnx for your help
#25
Originally Posted by maxedout95
Do you know if I can get a special relay for this set up?
I was thinking of running a extra wire from the fuse box to the turn signals but that would be my last option.
ThAnx for your help
I was thinking of running a extra wire from the fuse box to the turn signals but that would be my last option.
ThAnx for your help
Thread
Thread Starter
Forum
Replies
Last Post
03VQMAX
5th Generation Classifieds (2000-2003)
16
10-02-2016 09:36 AM
Maxilano
7th Generation Maxima (2009-2015)
1
08-31-2015 07:33 PM
kirkhilles
5th Generation Maxima (2000-2003)
2
08-08-2015 10:53 AM