Just blew motor.. DE-K swap help needed
#41
SCAMMER DO NOT BUY FROM FOR NOW
Thread Starter
iTrader: (5)
Join Date: Apr 2008
Location: Maryland
Posts: 657
ok, here is a video of the knocking noise i have... let me know what you think
http://www.youtube.com/watch?v=W6K3fULrDZs
http://www.youtube.com/watch?v=W6K3fULrDZs
#46
SCAMMER DO NOT BUY FROM FOR NOW
Thread Starter
iTrader: (5)
Join Date: Apr 2008
Location: Maryland
Posts: 657
i just changed my oil not too long ago but i will do that later on today. (put a video with the oil) one quick question, with the tensioner, bearing or rod would it be a instant thing that can go wrong or would it have to progress over time? because i have been hearing this noise for quite some time, if i would put the car in Neutral and rev it to 3k, it would do it. but it would be as loud as it is now.
Last edited by i2vicious2; 07-09-2008 at 04:38 AM.
#47
I think I mentioned TC tensioner before ... didn't I???? Oh, yea, I did! Have you done the tensioner? Maybe that'd be an easier job for a newby to start on that droppin in a whole other engine. Does it do it on start up? When it's cold? I can't believe that anyone would decide that the engine is shot without really checking it out. The TC tensioner is one of those "you're gonna have to replace eventually" parts anyhow ... so with that being said - I'd start there. Lot cheaper and MUCH easier than a whole swap.
#50
+1 on possibly being the TC tensioner. The audio quality isn't the best, but to me from the speed at which it is knocking (the engine is at idle in the video right?) and the deepness of the knock, it does NOT sound like bottom end rod knock to me.
Then again, I could definitely be wrong, but it could be worth checking out the TC tensioner first.
Then again, I could definitely be wrong, but it could be worth checking out the TC tensioner first.
#51
i finished my swap awhile ago me alone it took my 4 days bull ****ting around with no help so if you have a ? you can shoot me a pm i dropped the gearbox first then lifted the motor from above its honestly not hard if i did it in my driveway with 2 floor jacks and jack stands, handtools, a cherrypicker you can do it too lol
#52
SCAMMER DO NOT BUY FROM FOR NOW
Thread Starter
iTrader: (5)
Join Date: Apr 2008
Location: Maryland
Posts: 657
ok, so when i changed my oil, all i saw was metal shavings... like a failed or failing tranny, and i recently just changed my oil and its already black, i changed it about 350mi ago... but thats beyond the fact, everything is running smooth with me taking out the motor, i am going to rent a engine hoist today, i disconected everything and all i need is to take the motor out, the new one is suppose to arrive today, hopefully i have it out before that time...... so i can just swap the parts over, change the tc tensioner,water pump, and all the exterior belts
#53
ok, so when i changed my oil, all i saw was metal shavings... like a failed or failing tranny, and i recently just changed my oil and its already black, i changed it about 350mi ago... but thats beyond the fact, everything is running smooth with me taking out the motor, i am going to rent a engine hoist today, i disconected everything and all i need is to take the motor out, the new one is suppose to arrive today, hopefully i have it out before that time...... so i can just swap the parts over, change the tc tensioner,water pump, and all the exterior belts
#56
not sure what the fuss is over... yeah you have to swap out an engine now...but im assuming you are capable.
in the end you're gonna come out even money-wise (sell the 00vi to get your $400 back) and you're gonna have an engine with half the mileage. its a no brainer. go for it and good luck!
in the end you're gonna come out even money-wise (sell the 00vi to get your $400 back) and you're gonna have an engine with half the mileage. its a no brainer. go for it and good luck!
#57
I wish you luck mate .... Hope all goes well.
I think it was maybe a question as to weather it was actually needed in the first place. I still think you should have at least done a compression check. Just my .02 anyway. So ... what are you gonna do with the OEM engine?
I think it was maybe a question as to weather it was actually needed in the first place. I still think you should have at least done a compression check. Just my .02 anyway. So ... what are you gonna do with the OEM engine?
#58
SCAMMER DO NOT BUY FROM FOR NOW
Thread Starter
iTrader: (5)
Join Date: Apr 2008
Location: Maryland
Posts: 657
I'm probably just going to take the IM off and junk everything else, I really dont have a use for it... Maybe I'll tear it apart and check to see what the problem was. but everything is going smooth i took the old motor out and im swapping over the accessories now...
Last edited by i2vicious2; 07-12-2008 at 07:41 AM.
#64
#66
swap your fuel lines you might have them on back wards. check your all motor thread i posted more in there
http://forums.maxima.org/all-motor/5...-no-start.html
http://forums.maxima.org/all-motor/5...-no-start.html
Last edited by Product_Of_Korea; 07-13-2008 at 06:03 PM.
#69
SCAMMER DO NOT BUY FROM FOR NOW
Thread Starter
iTrader: (5)
Join Date: Apr 2008
Location: Maryland
Posts: 657
well the problem is fixed, the fuel injectors werent grounded properly, i didnt ground them to the IM because i thought the screw was stripped. so, i grounded them and it started without a problem..... thanks all...
#72
Its funny how I just helped him with his 00vi swap and he swaps his whole motor by himself less than a month later lol. The swap looks good he just has a few things to finish up but its running.
#74
damn it i was going to suggest that! when i didnt have my grounds hooked up though it didnt crank so i figured that wasnt the problem
#75
SCAMMER DO NOT BUY FROM FOR NOW
Thread Starter
iTrader: (5)
Join Date: Apr 2008
Location: Maryland
Posts: 657
i didnt have any pics or video to go along with my swap, just one pic with the 00vi off and the tranny out, but i just have a couple of vaccum leaks to get rid of, and ill be finished, this idling/revving is blowing me.
Thread
Thread Starter
Forum
Replies
Last Post
tsi6001
5th Generation Maxima (2000-2003)
12
10-03-2022 10:23 PM
TonyJr
3rd Generation Maxima (1989-1994)
4
08-20-2015 12:14 AM