4th Generation Maxima (1995-1999) Visit the 4th Generation forum to ask specific questions or find out more about the 4th Generation Maxima.

HELP!! PLZ Nostart no crank no nothing

Thread Tools
 
Search this Thread
 
Old 10-12-2011, 08:50 AM
  #1  
Member
Thread Starter
iTrader: (3)
 
blackmaxftw's Avatar
 
Join Date: Aug 2010
Location: maryland
Posts: 238
HELP!! PLZ Nostart no crank no nothing

I know so much about Maximas and i thought i would never have to post on here again but i did a dek swap and i drop the motor and transout at the same time and left the starter and everything attached i put it str8 into a 4thgen and hooked everything up .i get in turn the key and absolutely nothing happens when i turn the key to start it, everything else works fine all acc .any ideas ??? oh its a 5thgen trans and starter ive used a 5thgen trans before and did the wiring so i nothats not it and i swithed the pnp switch over from the 4thgen trans..........will a 5thgen starter work on a 4thgen engine harness????

Last edited by blackmaxftw; 10-12-2011 at 08:58 AM.
blackmaxftw is offline  
Old 10-12-2011, 09:11 PM
  #2  
Junior Member
iTrader: (1)
 
99superblackmax's Avatar
 
Join Date: Sep 2008
Location: Ann Arbor, MI
Posts: 66
That's a good question about the starter, not sure on that. Do the interior lights, illumination, etc. shut off when you try to start it? May have a loose ground somewhere. Is the security light on?
99superblackmax is offline  
Old 10-12-2011, 09:13 PM
  #3  
Junior Member
iTrader: (1)
 
99superblackmax's Avatar
 
Join Date: Sep 2008
Location: Ann Arbor, MI
Posts: 66
Didn't see starter on 4th gen harness. That is more than likely your problem. Could have different power and ground connections in the pigtail
99superblackmax is offline  
Old 10-12-2011, 10:05 PM
  #4  
Senior Member
iTrader: (2)
 
DennisMik's Avatar
 
Join Date: Apr 2004
Location: Plano, TX
Posts: 10,649
The electrical hookup to the starter is the same for 4th gen and 5th gen. Thick cable from the battery and thin wire from the ignition switch. The 4th gen uses 2 relays to get the power from the ignition switch to the starter solenoid (thin wire.) The 5.5 gen uses 1 relay. I don't know if the plastic connector is the same for the solenoid wire.
DennisMik is offline  
Old 10-13-2011, 10:20 AM
  #5  
Member
Thread Starter
iTrader: (3)
 
blackmaxftw's Avatar
 
Join Date: Aug 2010
Location: maryland
Posts: 238
So what should i check I checked the starter sig fuse and wheres the ign relay..........Oh and 1 more thing when i put the key to the on position and go under the hood and disconnect the negative battery cable usually i hear the relays click as i touch the cable to the neg post on batt when when i do this i hear absolutely nothing..........I tried this in my moms 4thgen and all relays and stuff under the hood clicked the egi relay click along with alot of other ones.....and her car start right up.
Originally Posted by DennisMik
The electrical hookup to the starter is the same for 4th gen and 5th gen. Thick cable from the battery and thin wire from the ignition switch. The 4th gen uses 2 relays to get the power from the ignition switch to the starter solenoid (thin wire.) The 5.5 gen uses 1 relay. I don't know if the plastic connector is the same for the solenoid wire.

Last edited by blackmaxftw; 10-13-2011 at 10:22 AM.
blackmaxftw is offline  
Old 10-13-2011, 11:59 AM
  #6  
Blown
iTrader: (81)
 
cardana24's Avatar
 
Join Date: May 2003
Location: Charlottesville, VA
Posts: 9,765
bad starter
ignition switch
bad battery
poor engine ground
corrosion on the battery terminals
fuse
is the car in park when you try to start it? Neutral safety switch?

I don't know the answer about the 5th gen starter, but I am guessing a multimeter would answer that question.
cardana24 is offline  
Old 10-13-2011, 02:04 PM
  #7  
Member
Thread Starter
iTrader: (3)
 
blackmaxftw's Avatar
 
Join Date: Aug 2010
Location: maryland
Posts: 238
I got the starter tested and it worked,didnt try the ignition switch yet and never had a problem with it ,i clean the engine ground,and brand new batt only 2 months old.......i switched the pnp switch twice and and i think the starter will work i put a 4th gen starter on and i dont even get a click from that either
blackmaxftw is offline  
Old 10-13-2011, 02:13 PM
  #8  
Senior Member
iTrader: (4)
 
luke95gxe's Avatar
 
Join Date: Jan 2010
Location: charlotte nc
Posts: 1,285
Originally Posted by blackmaxftw
I got the starter tested and it worked,didnt try the ignition switch yet and never had a problem with it ,i clean the engine ground,and brand new batt only 2 months old.......i switched the pnp switch twice and and i think the starter will work i put a 4th gen starter on and i dont even get a click from that either
its prolly a relay or fuse what u can do is turn the key to on and jump the starter with a jump wire from the battery to the trigger wire on the starter there are 2 relays beside the fuse box under the dash did u check them?
luke95gxe is offline  
Old 10-13-2011, 02:53 PM
  #9  
Senior Member
iTrader: (5)
 
Trini Boom's Avatar
 
Join Date: May 2009
Location: Brooklyn, NY
Posts: 2,406
I am pretty ceetain that the 00 - 01 starter should be a direct fit. As for the 02 - 03, that's where I think its different. Which one are you using?
Trini Boom is offline  
Old 10-13-2011, 03:39 PM
  #10  
Member
Thread Starter
iTrader: (3)
 
blackmaxftw's Avatar
 
Join Date: Aug 2010
Location: maryland
Posts: 238
the 01
blackmaxftw is offline  
Old 10-13-2011, 08:23 PM
  #11  
Junior Member
iTrader: (1)
 
99superblackmax's Avatar
 
Join Date: Sep 2008
Location: Ann Arbor, MI
Posts: 66
After all you have tried I would consider the ignition switch next. If swapping the 4th gen starter didn't help, it seems there's something happening between the ignition and starter
99superblackmax is offline  
Old 10-14-2011, 01:28 PM
  #12  
Member
Thread Starter
iTrader: (3)
 
blackmaxftw's Avatar
 
Join Date: Aug 2010
Location: maryland
Posts: 238
Still No nothing!!!
blackmaxftw is offline  
Old 10-14-2011, 01:56 PM
  #13  
Blown
iTrader: (81)
 
cardana24's Avatar
 
Join Date: May 2003
Location: Charlottesville, VA
Posts: 9,765
will the car start by manually bypassing the starter signal (grounding the starter)? I am not really suggesting you do this for safety reasons, but I have done this before to make cars start if the key will not turn the starter over.

*Disclaimer*

^^This will not fix your problem but if you have to have the car started it may get you out of a bind.

*also, have you tried charging you battery? I know you said it is new, but it would not hurt to make sure it has a full charge.*
cardana24 is offline  
Old 10-14-2011, 03:43 PM
  #14  
Member
Thread Starter
iTrader: (3)
 
blackmaxftw's Avatar
 
Join Date: Aug 2010
Location: maryland
Posts: 238
Yes i just finished doing this its like its not getting any ign signals from anywhere no gas or anything my fuel pump doesnt even prime ussually it buzzes but nothing i just checked that
blackmaxftw is offline  
Old 10-14-2011, 06:53 PM
  #15  
Senior Member
iTrader: (2)
 
DennisMik's Avatar
 
Join Date: Apr 2004
Location: Plano, TX
Posts: 10,649
Did you check the fuses under the hood? There is one labeled IGN SW that feeds the ignition switch. The ignition switch then feeds a lot of other things and the fuel pump and starter are among them.
DennisMik is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
TKHanson
5th Generation Maxima (2000-2003)
6
11-24-2018 01:39 AM
chisam14
6th Generation Maxima (2004-2008)
1
11-06-2018 08:56 PM
zmcneely13
4th Generation Maxima (1995-1999)
1
09-26-2015 02:26 PM
msellas
4th Generation Maxima (1995-1999)
2
09-23-2015 09:16 PM
conansriver
5th Generation Maxima (2000-2003)
0
09-11-2015 10:26 AM



Quick Reply: HELP!! PLZ Nostart no crank no nothing



All times are GMT -7. The time now is 04:34 PM.