Massive Napa gold 1182 oil filter
#1
Massive Napa gold 1182 oil filter
Today I got tired of trying to pass a mini game on Zelda and decided to trial fit my Napa Gold 1182 filter.
I had to remove some material with my Chraftsman angle die grinder. After removing some aluminum from above the pan rail gasket area it barely scrapes just enough to remove some paint from the can.
I then applied some of my daughters paint to the filter gasket and installed the filter. Sealing area looks great to me.
Luckily I was over full 1/2 a quart so removing and reinstalling the filter was not a big issue. All grinding was done with the small filter in place and then sprayed with brake cleaner and then air prior to removing the filter again. The car was not run with the 1182 filter, that will wait until the oil change in about 1.5K.
Wix 57356 maxima filter
Style:Spin-On Lube
FilterService:Lube
Type:Full Flow
Media:Paper
Height:3.402
Outer Diameter Top:2.685
Outer Diameter Bottom:Closed
Thread Size:20X1.5 MM
By-Pass Valve Setting-PSI:8-11
Anti-Drain Back Valve:Yes
Beta Ratio:2/20=6/20
Burst Pressure-PSI:363
Max Flow Rate:9-11 GPM
Nominal Micron Rating:21
Wix 51182
Style:Spin-On Lube Filter
Service:Lube
Type:Full Flow
Media:Paper
Height:5.207
Outer Diameter Top:3.66
Outer Diameter Bottom:Closed
Thread Size:20X1.5 MM
By-Pass Valve Setting-PSI:24
Anti-Drain Back Valve:Yes
Beta Ratio:2/20=6/20
Burst Pressure-PSI:350
Max Flow Rate:7-9 GPM
Nominal Micron Rating:21
Acording to the guys at Bob in The Oil Guy, this filter will outflow a VQ by sometiing like 5X.
I had to remove some material with my Chraftsman angle die grinder. After removing some aluminum from above the pan rail gasket area it barely scrapes just enough to remove some paint from the can.
I then applied some of my daughters paint to the filter gasket and installed the filter. Sealing area looks great to me.
Luckily I was over full 1/2 a quart so removing and reinstalling the filter was not a big issue. All grinding was done with the small filter in place and then sprayed with brake cleaner and then air prior to removing the filter again. The car was not run with the 1182 filter, that will wait until the oil change in about 1.5K.
Wix 57356 maxima filter
Style:Spin-On Lube
FilterService:Lube
Type:Full Flow
Media:Paper
Height:3.402
Outer Diameter Top:2.685
Outer Diameter Bottom:Closed
Thread Size:20X1.5 MM
By-Pass Valve Setting-PSI:8-11
Anti-Drain Back Valve:Yes
Beta Ratio:2/20=6/20
Burst Pressure-PSI:363
Max Flow Rate:9-11 GPM
Nominal Micron Rating:21
Wix 51182
Style:Spin-On Lube Filter
Service:Lube
Type:Full Flow
Media:Paper
Height:5.207
Outer Diameter Top:3.66
Outer Diameter Bottom:Closed
Thread Size:20X1.5 MM
By-Pass Valve Setting-PSI:24
Anti-Drain Back Valve:Yes
Beta Ratio:2/20=6/20
Burst Pressure-PSI:350
Max Flow Rate:7-9 GPM
Nominal Micron Rating:21
Acording to the guys at Bob in The Oil Guy, this filter will outflow a VQ by sometiing like 5X.
Last edited by asand1; 01-13-2013 at 07:06 PM.
#6
I went ahead and changed the oil 641 miles early today. Startup was as quiet as any other startup after an oil change.
The reason for the larger filter is two-fold. Both reasons are related to the extra oil capacity.
1 I like the idea of using the whole 5qt jug rather than having extra oil take up space in my small garage.
2 I feel better about stretching the OCI to 5K+ with the extra .75qt.
As far as being a dead ringer, the bypass is 24 rather than 8-11, but with the larger media I believe the pressure differential will be close to the same.
The reason for the larger filter is two-fold. Both reasons are related to the extra oil capacity.
1 I like the idea of using the whole 5qt jug rather than having extra oil take up space in my small garage.
2 I feel better about stretching the OCI to 5K+ with the extra .75qt.
As far as being a dead ringer, the bypass is 24 rather than 8-11, but with the larger media I believe the pressure differential will be close to the same.
#8
OK, devil's advocate.
The engine rattles when the oil pump is spinning strongly at 3K rpms. Not a good sign. This would suggest that, if you downgrade to a smaller filter, one that is still bigger than OEM, and the rattle goes away, BUT, would you not remained concerned that oil is not getting as much oomph going through all those oil passages as the OEM filter for the very same reasons?
Yeah, no rattle, but still. Fact is, from your first experiment, the bigger filter is robbing pressure or flow or what have you.
Perhaps a beefier, faster pumping oil pump is in order as well. But then that gets real complicated I imagine.
#10
OK, devil's advocate.
The engine rattles when the oil pump is spinning strongly at 3K rpms. Not a good sign. This would suggest that, if you downgrade to a smaller filter, one that is still bigger than OEM, and the rattle goes away, BUT, would you not remained concerned that oil is not getting as much oomph going through all those oil passages as the OEM filter for the very same reasons?
Yeah, no rattle, but still. Fact is, from your first experiment, the bigger filter is robbing pressure or flow or what have you.
Perhaps a beefier, faster pumping oil pump is in order as well. But then that gets real complicated I imagine.
The engine rattles when the oil pump is spinning strongly at 3K rpms. Not a good sign. This would suggest that, if you downgrade to a smaller filter, one that is still bigger than OEM, and the rattle goes away, BUT, would you not remained concerned that oil is not getting as much oomph going through all those oil passages as the OEM filter for the very same reasons?
Yeah, no rattle, but still. Fact is, from your first experiment, the bigger filter is robbing pressure or flow or what have you.
Perhaps a beefier, faster pumping oil pump is in order as well. But then that gets real complicated I imagine.
#12
I went ahead and installed a 1347.
Here's the Oil Filter's specs:
Part Number: 51347
Media: Paper
Height: 4.828
Outer Diameter Top: 2.921
Outer Diameter Bottom: Closed
Thread Size: 20X1.5 MM
By-Pass Valve Setting-PSI: 8-11
Anti-Drain Back Valve: Yes
Beta Ratio: 2/20=6/20
Burst Pressure-PSI: 325
Max Flow 9-11 GPM
Nominal Micron Rating: 21
Gasket Diameters
Number O.D. I.D. Thk.
Attached 2.734 2.430 0.226
Borrowed this pic from my 350z
Here's the Oil Filter's specs:
Part Number: 51347
Media: Paper
Height: 4.828
Outer Diameter Top: 2.921
Outer Diameter Bottom: Closed
Thread Size: 20X1.5 MM
By-Pass Valve Setting-PSI: 8-11
Anti-Drain Back Valve: Yes
Beta Ratio: 2/20=6/20
Burst Pressure-PSI: 325
Max Flow 9-11 GPM
Nominal Micron Rating: 21
Gasket Diameters
Number O.D. I.D. Thk.
Attached 2.734 2.430 0.226
Borrowed this pic from my 350z
Last edited by asand1; 02-11-2013 at 06:37 PM.
#13
#14
Yes, at 49 degrees I waited till 3K to shift into third. I am running 5W30 Castrol GTX. This was never a problem with a stock type filter.
Thread
Thread Starter
Forum
Replies
Last Post
my03maxima
7th Generation Maxima (2009-2015)
9
07-28-2024 07:40 AM
My Coffee
New Member Introductions
15
06-06-2017 02:01 PM