Bone Stock Dyno Run?
#1
Bone Stock Dyno Run?
Does anyone have a dyno slip of a Bone stock 03 6spd doing a Dyno run. I didnt get a chance to hit the dyno before I installed my headers, so Id like a ballpark figure for comparison.
If you have a slip with a dyno run with a stocker with Berk intake, that will give me an even better basis for comparison.
Now hopefully I can resist the temptation to install my UDP before my dyno time on the 27th..... ugh!
Cmon 240whp!!!
If you have a slip with a dyno run with a stocker with Berk intake, that will give me an even better basis for comparison.
Now hopefully I can resist the temptation to install my UDP before my dyno time on the 27th..... ugh!
Cmon 240whp!!!
#3
200 to 208 whp is typical....
DYNO forum is your friend: http://forums.maxima.org/showthread.php?t=282615
DYNO forum is your friend: http://forums.maxima.org/showthread.php?t=282615
#7
Originally Posted by 01GreyLustreSE
hmmmm i wonder if i have one... im 01 i just did a burnout like 5 min ago and both tires where spinning.. both tires left marks
#9
Originally Posted by NmexMAX
212-220 wh/tq typically
MaximaDave's stock 2k2 got 204/219...
#10
Originally Posted by Puppetmaster
I still think that's a little high since I'm pretty sure the stock 03 #s were overrated just like the 02s.... got dyno?
MaximaDave's stock 2k2 got 204/219...
MaximaDave's stock 2k2 got 204/219...
5.5 gens are powered by the same engine that the Murano uses: 245HP/246TQ
#12
Originally Posted by NmexMAX
Read post again ... Torque ... .. I wasn't referring to HP ...
#16
I don't think its that hard to hit 240whp? Rbrown what do u have? I/H/E right?
yeah 240whp should be easy for u...there are a few guys who dynoed with 233-235whp with a stock cat and stock catback....so i'm thinkin, with u having an exhaust over them, you should get 240whp
yeah 240whp should be easy for u...there are a few guys who dynoed with 233-235whp with a stock cat and stock catback....so i'm thinkin, with u having an exhaust over them, you should get 240whp
#18
I will have a bone stock 2k2 6 speed with HLSD dyno done very soon. I put my car back to absolute stock so I could get a good baseline before adding the Cattman Gen II headers.
I went as far as putting back in the original air filter that came in it from the factory.
I went as far as putting back in the original air filter that came in it from the factory.
#19
Originally Posted by 6spd_Hayes
I will have a bone stock 2k2 6 speed with HLSD dyno done very soon. I put my car back to absolute stock so I could get a good baseline before adding the Cattman Gen II headers.
I went as far as putting back in the original air filter that came in it from the factory.
I went as far as putting back in the original air filter that came in it from the factory.
Thread
Thread Starter
Forum
Replies
Last Post
The Frye
7th Generation Maxima (2009-2015)
6
09-02-2021 11:03 AM
Maxima30
5th Generation Maxima (2000-2003)
2
09-07-2015 06:13 PM
trungg86
4th Generation Maxima (1995-1999)
7
09-04-2015 04:58 AM
Justin Kroll
5th Generation Maxima (2000-2003)
7
09-02-2015 11:06 AM