Kelford cams for the VQ35
#89
wow pretty harsh words there guys, condering the man is in AU and the time differnce, you guys jump on him and hes probally busy with family matters ?
why does it seems that someone post something( like the RB maxima) everyone seems to jump on someones back before even knowing the facts ?
hes building his car for himself not for the fourms.
give the guy some slack , not everyone a fourm junkie , esp if hes on the other side of the earth
why does it seems that someone post something( like the RB maxima) everyone seems to jump on someones back before even knowing the facts ?
hes building his car for himself not for the fourms.
give the guy some slack , not everyone a fourm junkie , esp if hes on the other side of the earth
#91
wow pretty harsh words there guys, condering the man is in AU and the time differnce, you guys jump on him and hes probally busy with family matters ?
why does it seems that someone post something( like the RB maxima) everyone seems to jump on someones back before even knowing the facts ?
hes building his car for himself not for the fourms.
give the guy some slack , not everyone a fourm junkie , esp if hes on the other side of the earth
why does it seems that someone post something( like the RB maxima) everyone seems to jump on someones back before even knowing the facts ?
hes building his car for himself not for the fourms.
give the guy some slack , not everyone a fourm junkie , esp if hes on the other side of the earth
#92
That throttlehappy46 guy is on 50 forums claiming he has 50 cars that are probably worth a combined $5million.... he always claiming he is building something, this or that, or has this, but never shows any proof of having anything... Smart guy and knows his stuff for the most part but never seen any real proof or facts backing up anything he does.
#94
http://freepdfhosting.com/680f54aee4.pdf is the current design All measurements are in millimetres Total thickness of the flywheel is 25mm, which allows for the friction plate closest to the flywheel to be worn down to nothing and still not cause the splines to rub on the crankshaft or flywheel bolts.
The car is now finished and videos of idle lope, driving along with a 1/4 mile run will be upload and posted.
#96
1/4 mile time was not great due to track surface BUT the MPH speaks for itself. Its in the video
Quartermaster and I should have the clutch setup sorted for production. I have been working with them as this clutch + flywheel design will also work with the QR25 and SR20 I have not told them that yet BUT I am sure they will figure it out once a few cheap ones have been sold to VQ/QR/SR owners
Quartermaster and I should have the clutch setup sorted for production. I have been working with them as this clutch + flywheel design will also work with the QR25 and SR20 I have not told them that yet BUT I am sure they will figure it out once a few cheap ones have been sold to VQ/QR/SR owners
Last edited by throttlehappy46; 06-13-2010 at 09:36 AM.
#108
he has recently installed C9 cams but again results would be differnt VS ,
stock DE
VS
high compression DE
#110
which would be a good intake manifold good for my engine that has JWT pistnes c9 11.1
this would be good http://cgi.ebay.com/ebaymotors/Kinet...0QQcmdZViewIte
b14 vq35 12.2 a 111 HALTEC PLATINUM Pipe 3 " q45 throttle body
http://www.youtube.com/watch?v=_l20kHa337k
http://www.youtube.com/watch?v=IrkZr_89W_s
Last edited by YANvq35; 08-12-2010 at 04:36 AM.
#111
which would be a good intake manifold good for my engine that has JWT pistnes c9 11.1
this would be good http://cgi.ebay.com/ebaymotors/Kinet...0QQcmdZViewIte
b14 vq35 12.2 a 111 HALTEC PLATINUM Pipe 3 " q45 throttle body
http://www.youtube.com/watch?v=_l20kHa337k
http://www.youtube.com/watch?v=IrkZr_89W_s
this would be good http://cgi.ebay.com/ebaymotors/Kinet...0QQcmdZViewIte
b14 vq35 12.2 a 111 HALTEC PLATINUM Pipe 3 " q45 throttle body
http://www.youtube.com/watch?v=_l20kHa337k
http://www.youtube.com/watch?v=IrkZr_89W_s
if your aiming for all motor why not try a set of Jenvey ITBs ?
We have them running on a customer car , hes a member on here kgleen101
#112
Thread
Thread Starter
Forum
Replies
Last Post