5th Gen Gauge Pods
...
Originally posted by Custommaxima.com
And a gauge bezel too.
And a gauge bezel too.
YOUR KIDDING right!
That's the one that has two SMALLER gauges on either side of the tach/speedometer, right?
If so, I'll take one of those also.
In carbon fiber? 
Wooo Hooo... this was my suggestion months ago 
Originally posted by Custommaxima.com
I just took care of you guys. Contacted Lo-Tek and placed an order for 60 gauge pods. He needs the factory pods which I already ordered from nissan (which were dang expensive) and will be shipping to Lo Tek for them to match it. We contracted a deal to also produce new 95-99 pillars that will be a complete pillar instead of the pods as autometer makes. According to Lo-Tek they should be done September. Color will also be matched also. CustomMaxima.com already commited to 30 95-99 pods and 30 2000+ pods so they will start production as soon as they receive the factory pillars. Any questions just ask.
Thanks,
Greg
Greg@CustomMaxima.com
I just took care of you guys. Contacted Lo-Tek and placed an order for 60 gauge pods. He needs the factory pods which I already ordered from nissan (which were dang expensive) and will be shipping to Lo Tek for them to match it. We contracted a deal to also produce new 95-99 pillars that will be a complete pillar instead of the pods as autometer makes. According to Lo-Tek they should be done September. Color will also be matched also. CustomMaxima.com already commited to 30 95-99 pods and 30 2000+ pods so they will start production as soon as they receive the factory pillars. Any questions just ask.
Thanks,
Greg
Greg@CustomMaxima.com
. Way to go Greg!
Donating Maxima.org Member
Joined: Aug 2001
Posts: 2,267
Originally posted by big h
give me the guage bezel and im happy, happy, happy.
give me the guage bezel and im happy, happy, happy.
...
Originally posted by Tanman
Are you all planning to use the gauge bezel as well as the A-pillar pods? What 5 gauges do you plan to use? Let's not over-do it folks, we're heading into rice territory here...
Are you all planning to use the gauge bezel as well as the A-pillar pods? What 5 gauges do you plan to use? Let's not over-do it folks, we're heading into rice territory here...
My list:
1)EGT
2)Fuel Pressure
3)Nitrous Pressure
4)Oil pressure
5)Oil temp
6)A/F
I'm also hoping to figure out how to make a KNOCK sensor output gauge.
Other possibilities:
7)Boost/Vacuum
8)Tranny temperature for autos
9)Intake air temp
10)Fuel temp
11)Coolant temp
12)Volts
If I had enough room I'd have them all.
Senior Member
Joined: Aug 2002
Posts: 1,280
Re: ...
Originally posted by IceY2K1
Both unless the HKS CAMP works out.
My list:
1)EGT
2)Fuel Pressure
3)Nitrous Pressure
4)Oil pressure
5)Oil temp
6)A/F
I'm also hoping to figure out how to make a KNOCK sensor output gauge.
Other possibilities:
7)Boost/Vacuum
8)Tranny temperature for autos
9)Intake air temp
10)Fuel temp
11)Coolant temp
12)Volts
If I had enough room I'd have them all.
Both unless the HKS CAMP works out.
My list:
1)EGT
2)Fuel Pressure
3)Nitrous Pressure
4)Oil pressure
5)Oil temp
6)A/F
I'm also hoping to figure out how to make a KNOCK sensor output gauge.
Other possibilities:
7)Boost/Vacuum
8)Tranny temperature for autos
9)Intake air temp
10)Fuel temp
11)Coolant temp
12)Volts
If I had enough room I'd have them all.
I would be all over a gauge bezel.
Alright does ANYONE know what the status is on these Gauge Pods? He supposedely shouldve gotten a prototype in laste August or early september.
Also what has been the final outcome? We doing 2 1/16" or 60mm? Cause Im about to buy gauges for my Supercharger which will be installed next weekend. Need to know what I need to get so I dont buy the wrong size.
Dixit
Also what has been the final outcome? We doing 2 1/16" or 60mm? Cause Im about to buy gauges for my Supercharger which will be installed next weekend. Need to know what I need to get so I dont buy the wrong size.
Dixit
Originally posted by Custommaxima.com
Got a call from Lo-Tek yesterday, they will have a prototype to me next week. I will take pictures and post them for you to see.
-Greg
Got a call from Lo-Tek yesterday, they will have a prototype to me next week. I will take pictures and post them for you to see.
-Greg
Donating Maxima.org Member
Joined: Aug 2001
Posts: 2,267
Originally posted by BlackMax2k1
Are these easy to install or do you have to take the whole dash apart?
Are these easy to install or do you have to take the whole dash apart?
Originally posted by Tanman
You mean the pillar or the gauges themselves? The gaugepods\pillar is simple, pull off the old piece, snap in the new piece. Gauges are a bit more difficult and involve drilling, running sensor wires, installing sensors, splicing into fluid lines, etc. Best left to a professional.
You mean the pillar or the gauges themselves? The gaugepods\pillar is simple, pull off the old piece, snap in the new piece. Gauges are a bit more difficult and involve drilling, running sensor wires, installing sensors, splicing into fluid lines, etc. Best left to a professional.
Donating Maxima.org Member
Joined: Aug 2001
Posts: 2,267
Originally posted by BlackMax2k1
I meant the gauges and it sounds like too much work to me.
I meant the gauges and it sounds like too much work to me.
.Toylet:
They're not available yet. Greg posted on Sept 13 that he would receive them next week (last week now). I checked his website, no news or pictures of the pod.
Originally posted by Tanman
Toylet:
They're not available yet. Greg posted on Sept 13 that he would receive them next week (last week now). I checked his website, no news or pictures of the pod.
Toylet:
They're not available yet. Greg posted on Sept 13 that he would receive them next week (last week now). I checked his website, no news or pictures of the pod.
Originally posted by Custommaxima.com
Got a call from Lo-Tek yesterday, they will have a prototype to me next week. I will take pictures and post them for you to see.
-Greg
Got a call from Lo-Tek yesterday, they will have a prototype to me next week. I will take pictures and post them for you to see.
-Greg
