Another KS question, should be easy
11-29-2005, 01:18 PM
#1
Another KS question, should be easy
Hello, I have a knock sensor that i bought for my 93, when i bought it i wasnt asked to specify between DOHC or SOHC i assumed they were the same but when i called the dealer earlier trying to figure out my question below they said that its a different sensor depending on DOHC vs SOHC. Im trying to sell the knocksensor as I later determined i dont need it, and i believe some one told me that the knocksensor is the same between a 3rd gen and a 4th gen....but will a knocksensor for a SOHC work in a 4th gen which are all DOHC?
Thanks Nick
Thanks Nick
11-29-2005, 01:28 PM
#3
btw..This info took me about 30 seconds to find in the stickies....
http://forums.maxima.org/showpost.ph...10&postcount=5
http://forums.maxima.org/showpost.ph...10&postcount=5
11-29-2005, 02:37 PM
#4
hunh?
the VG (SOHC) screws into the block.
the VE and VQ use one with a hole in the middle and a bolt goes through it.
They are not the same
VG = 22060-56s10
VE and VQ=22060-30p00
the VG (SOHC) screws into the block.
the VE and VQ use one with a hole in the middle and a bolt goes through it.
They are not the same
VG = 22060-56s10
VE and VQ=22060-30p00
11-29-2005, 03:32 PM
#5
Originally Posted by internetautomar
hunh?
the VG (SOHC) screws into the block.
the VE and VQ use one with a hole in the middle and a bolt goes through it.
They are not the same
VG = 22060-56s10
VE and VQ=22060-30p00
the VG (SOHC) screws into the block.
the VE and VQ use one with a hole in the middle and a bolt goes through it.
They are not the same
VG = 22060-56s10
VE and VQ=22060-30p00
I got this info from your o.e parts locator sticky..in the stickies..
11-29-2005, 03:46 PM
#6
try pulling it up for a 91 (VG motor only) they don't list it, so I had to use some of my other sources to pull it up.
The VG motor has it's knock sensor mounted on the rear of the block by the exhaust manifold
The VG motor has it's knock sensor mounted on the rear of the block by the exhaust manifold
11-29-2005, 03:56 PM
#7
Originally Posted by internetautomar
try pulling it up for a 91 (VG motor only) they don't list it, so I had to use some of my other sources to pull it up.
The VG motor has it's knock sensor mounted on the rear of the block by the exhaust manifold
The VG motor has it's knock sensor mounted on the rear of the block by the exhaust manifold
Ahhh..I am so used to using 94 as the default yr. in the idiotzone sticky...I'm a
again...
11-30-2005, 01:40 PM
#9
Originally Posted by internetautomar
hunh?
the VG (SOHC) screws into the block.
the VE and VQ use one with a hole in the middle and a bolt goes through it.
They are not the same
VG = 22060-56s10
VE and VQ=22060-30p00
the VG (SOHC) screws into the block.
the VE and VQ use one with a hole in the middle and a bolt goes through it.
They are not the same
VG = 22060-56s10
VE and VQ=22060-30p00
Thanks
11-30-2005, 03:57 PM
#11
Originally Posted by Alex_V
Why does a VG have a knock snesor if its ignition isnt eletronicly controlled? or does it tap into the coil power and delay it?
~Alex
~Alex
Thread
Thread Starter
Forum
Replies
Last Post
James92SE
3rd Generation Maxima (1989-1994)
142
01-02-2024 09:23 AM
Unclejunebug
5th Generation Maxima (2000-2003)
10
04-02-2016 05:42 AM
pears
5th Generation Maxima (2000-2003)
15
09-18-2015 05:25 AM