kramarz99

did some research and couldn't`t find it. there is tread how to install o2 sim on California edition maxima. I got 2000 federal edition and getting p0135 and p0155 ses. just want to know how to hook up 02 simulator. got the dual output one. can someone post some pics of location where to splice and attach o2 simulator?

thanks

kramarz99

does anyone know how to get ridde off P0135 and P0155 alarms with 02 simulator? where and how to hook it up?

kramarz99

some help, please..................

Puppetmaster

iTrader: (48)

Aren't those heater codes for the primary sensors? The sim will not fix those; the sim is only meant for voltage codes on the secondary O2s.

Also, are you sure you have a P0141? That's for a Cali spec car. That's a heater code for a secondary, that will the sim will not fix either.

You have to get new sensors or some resistors to simulate the heater circuit.

Someone correct me if I'm off base, because I'm on vicodin now, lol.

kramarz99

see, before I had P0141 SES..after I hooked up o2 sim got 135 and 155? why would it do that? if I get resistor, wherehow do I install it?
this would be nice write up for a lot of members. I have been looking for write like this and couldn`t find it...

sergey85

iTrader: (2)

(p0135)This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

po155 (heater circuit bank 2 sensor 1) and P0141 O2 Sensor heater Circuit malfunction these are probably related. so like puppetmaster said probably need to replace them or take a look at it. i think the simulatar is used when getting the y pipe i believe for the secondary o2 sensors good luck

kramarz99

so there is no way to use simulator and bypass those? and, are we talking about 1 sensor or two?

SoonerFan

iTrader: (5)

P0135 - Front O2 Sensor Heater (Bank 1)
P0141 - Rear O2 Sensor Heater (Bank 1)
P0155 - Front O2 Sensor Heater (Bank 2)

3 sensors
Bank 1 - both sensors
Bank 2 - Primary sensor

why dont you just replace the sensors

kramarz99

just want to get ridde off SES light for good...how can I do that?

SoonerFan

iTrader: (5)

replace the bad O2 sensors

kramarz99

this will sound stupid, but how many sensors? just don`t laught...

Puppetmaster

iTrader: (48)

http://forums.maxima.org/showpost.ph...53&postcount=8

kramarz99

damn...that is like $300...any other options?

SoonerFan

iTrader: (5)

here are the locations
http://maxima.theowensfamily.com/tsb/NTB02-051a.pdf

you only have 3 sensors...all of them need to be replaced

SoonerFan

iTrader: (5)

dont drive your car

kramarz99

.....................

SoonerFan

iTrader: (5)

do you know what the sensors are for?

kramarz99

on that 4 wire sensor, are thos two white wires the same?

kramarz99

is it possible not to get power to o2 sensor?

SoonerFan

iTrader: (5)

if it isnt plugged in

kramarz99

so that what it was....lol
one more thing, on for wire sensor, how do you tell difference between thos two white wires?
how can you what is what?

Lugubrious

iTrader: (2)

I got the same problem PO135, PO155 and PO141. i have a Y pipe and hi flow cat converter with 140,000 plus miles. Car still runs like a champ! I've changed out all three O2 sensors and now I'm thinking that it might be the ECM. It might also be getting the wrong O2 sensors? Any suggestions?

mhernand99

I had the same p 0135 code come up on my 2001 maxima. I went ahead and changed the O2 sensor but my local auto parts store only had the NTK 24619 and not the Bosch. The Bosch is much bulkier so I am wondering if the NTK does not have the heater element. Has anyone used the NTK sensor?

I am just hoping the check engine light does not come on again.

williamgd2

There is a chance he is not getting power to the sensors. Check fuse #8 on the in car fuse block.