Ok, i'm starting my engine project....
#41
Ah just a note. When doing this type of modification, you should almost NEVER rely on someone else's info(unless it's super source). So if you are serious about this type of work, you probably should be mic'ing all the measurements your self. ie.. bore, bearing size, piston size, ring size etc.... or buy a Nissan service manual. If you are trying to do major engine work w/o one for assembly or just for reference, you are crazy.
#42
Well, all of the work will be done by a machine shop, and by my friends at an install shop....so I won't be touching it that much. I think I would need to go to them with guidelines though....
-Mike
-Mike
#43
bump.....
I'm going to talk to MardiGrasMax today and he's gonna help me figure out what parts I should get and some values.....I had talked to Y2KevSE a while ago, and he had given me some good ideas as well.....I'll let ya know what I decide....
-Mike
I'm going to talk to MardiGrasMax today and he's gonna help me figure out what parts I should get and some values.....I had talked to Y2KevSE a while ago, and he had given me some good ideas as well.....I'll let ya know what I decide....
-Mike
#44
Originally posted by Screaminfast
bump.....
I'm going to talk to MardiGrasMax today and he's gonna help me figure out what parts I should get and some values.....I had talked to Y2KevSE a while ago, and he had given me some good ideas as well.....I'll let ya know what I decide....
-Mike
bump.....
I'm going to talk to MardiGrasMax today and he's gonna help me figure out what parts I should get and some values.....I had talked to Y2KevSE a while ago, and he had given me some good ideas as well.....I'll let ya know what I decide....
-Mike
-pete
#45
Originally posted by Screaminfast
Does anyone know where the stock numbers are? Say for bore and stroke and cams and other stuff?? If I can go to the companies with these numbers, they might be able to help me out in choosing what I would need to get??
Thanks,
Mike
Does anyone know where the stock numbers are? Say for bore and stroke and cams and other stuff?? If I can go to the companies with these numbers, they might be able to help me out in choosing what I would need to get??
Thanks,
Mike
#46
Originally posted by gtr_rider
3.66 inch bore by 2.89 inch stroke
3.66 inch bore by 2.89 inch stroke
I just contacted DPR racing in Cali too because I would like to have them do my headwork......I tried to contact TurboMax95, but he hasn't replied. I'm trying to find out how I can get a custom and thicker copper head gasket..hehe
Anyone know?
Thanks,
Mike
#47
Ok, I need some ideas for an intercooler. Anyone have an Air to water intercooler here? I know my engine will be able to take a lot of Pressure, but at the same time I know the best I can do on the V2 is a 2.87" pulley. Anyone have some good ideas for a low pressure drop AWIC??
-Mike
-Mike
#48
I'm pretty sure he ended up using stock gaskets, couldn't find anyone to make them for a decent price.
Originally posted by Screaminfast
Thanks....
I just contacted DPR racing in Cali too because I would like to have them do my headwork......I tried to contact TurboMax95, but he hasn't replied. I'm trying to find out how I can get a custom and thicker copper head gasket..hehe
Anyone know?
Thanks,
Mike
Thanks....
I just contacted DPR racing in Cali too because I would like to have them do my headwork......I tried to contact TurboMax95, but he hasn't replied. I'm trying to find out how I can get a custom and thicker copper head gasket..hehe
Anyone know?
Thanks,
Mike
#49
Thread
Thread Starter
Forum
Replies
Last Post
MaximaDrvr
7th Generation Maxima (2009-2015)
16
08-19-2015 08:20 PM