vinco

iTrader: (3)

Ditto with an '00. Fully loaded SE, leather, sunroof, side airbags, 17" wheels, heated seats & mirrors, Bose, 5 spd, homelink, dual power seats, and whatever else you can think of. Anyone got a copy of a window sticker from a car like that?

Doggus

2000 Maxima ~100k mileage here. P0140 code diagnosed by AutoZone as the O2 sensor. So I bought the generic one and proceeded to replace. I'm guessing there is no way I could have screwed the wire splice up as the one I pulled out was a Bosch and the one I put in was a Bosch. They had identical wire colors. Followed the pamphlet to the letter. Problem is getting worse.

Car dies while sitting at a light. Needs to warm up first before putting in gear or it will putter and die. Exhaust smells really gassy. To me this all points to a bad sensor but I replaced it and still no dice.

Also if I throw another sensor at it, this time the OEM, where does it plug in? I noticed the wiring goes through the panel on the underbelly. I'm guessing that plate comes off and I'll see it under there?

hammester

My 03 Maxima is fully loaded except for the navigation system and the sticker price was a little over 30K.

98maxse5spd

iTrader: (5)

What are the differences between a 2002 and 2003 SE?

nebojsa_o

iTrader: (1)

As far as I know nothing, except for the availablity of the Titanium Edition, which probably added to the price. Maybe the '03's are more likely to have HLSD, my '02 doesn't. It was a early one...

nyautostyle

exactly. they're the same but the 03's had the titanium edition

K20z1_rsx

iTrader: (2)

I have an 03 Ti edition but it doesn't have a HLSD. And I had to drive 5 1/2 hours to buy my 6 speed when shopping for a max.

nebojsa_o

iTrader: (1)

Worth every minute though.

ghostridden

iTrader: (2)

needing to replace my intake manifold GASKETS, upper and lower, idiotzone only offers the upper, NO OTHER PART STORE even offers either of them. Can someone point me to a damn place that will sell the set for me, THANKS

Zack

hooch00

2000 maxi se

passenger headlight switches on and off after the car has been idling for 4-5 minutes. as the light switches off, the high beam indicator in the gauges turns on. when the light comes back on, the indicator turns off.

no problem whatsoever when the car is being driven, only after it has idled for a few minutes. all connections seem fine.

ideas?

blkAEmax82

iTrader: (16)

Did you try Dave B

DAVEB's number for OEM parts is
888-254-6060 and his email is daveb@adpub.com.

Patrick.R

Is a IACV on a 2k max the same as one for a 5.5 max?

Nicktard

Ok I need a lot of help, I ordered a lot of bulbs and my situation only keeps getting worse, ive made diagrams for better help. Very mad with the outcome so far, I should have just gone with getting an HID kit.

When looking in from above...I see a "female" harness that would take the end of a 9003 Bulb...also, coming from my lamp assembly there is a "male" plug? They plug into each other which and my lamp is an H3? lol. Could I just put a 9003 in and plug my "female" end into it?

Sorry for picture quality and stuff. I tried. Please Help me find the right products!

9003/H4's i have coming in the mail:
http://www.sfxperformance.com/parts/PIA15224.htm

Pic of parts:
http://i26.photobucket.com/albums/c1...ktard/GEEZ.jpg

My lights, and stuff:
http://i26.photobucket.com/albums/c1...ard/lights.jpg

Actual install:
http://i26.photobucket.com/albums/c1...tard/Light.jpg

Ask for any more pics or anything please.

jbrooks870

iTrader: (4)

I was wondering how much brand new OEM coil springs cost? I cant find them online. Thanks.

NmexMAX

iTrader: (22)

Browse the classifieds on here.

Nightkid08

iTrader: (20)

Ok. I have a 5.5 gen and ever since i bought it the driver seat feels very soft or worn. And the question i was wondering is if there are alternative OEM seats or AEM bucket seats in the market that has a solid feel and actually can hold you in the seat when your cornering when your making sharper turns. Thanks.

SunDown13X

iTrader: (1)

Regarding ELECTRONIC MOTOR MOUNTS...

Here is my vin number, if it helps... I should be back in NC tonight, so I will check for those wires using the link that you posted earlier.

2000 Maxima GLE
JN1CA31A6YT031950

It was build on 05/2000 according to the door sticker.

D.

SunDown13X

iTrader: (1)

for the record, my buzzing noise happens after i rev the car pass 5k to redline. It doesnt happen when I turn the car off as stated on the link you posted http://www.nissanhelp.com/Ownership/.../NTB01-010.htm

Nicktard

Okay so after messing with my lights once again, I think with buying my new light assembly it changed the bulbs I need. The factory plug no longer goes from car to light, it goes from car to headlight plug. I think this plug changes my bulbs.

Also, on the front of the assembly, in front of the high beam it says H1, Low beam H3. I bought H3's for my fogs and I put them in my lows temporarily and they fit perfect. So do you think I can order a Xenon H3 HID kit and install should be pretty straight foward or what?

Do bulb types:H1,H3,9003,4,5,6 ...etc, All have the same intensity, just different sizes? or do the different numbers have different intensity? Im just wondering if H3's will be bright enough for my lows.

Eastern

When looking at pictures of the front seats/dashes of 5th gens, I usually see the DC plug not being used while objects are still being powered that requires a DC plug. Where do you get this power, do you just use the backseat plug?

irish44j

iTrader: (38)

I have a couple auxiliary DC plugs hardwired into mine (radio shack 2 plug + cig lighter). That's where I power my ipod, phone, etc from. It's mounted to the side of the shift assembly on the passenger's side.

or, use the rear outlet.

daesonn

Can anyone tell me if i'm going to be happy with these tail lights?

http://cgi.ebay.com/ebaymotors/00-01...spagenameZWDVW

they're aftermarket, is there any difference, or should I go ahead and get these? the stock ones are too expensive for me to get, unless someone online here has an extra pair of SE tails theyd sell to me.

irish44j

iTrader: (38)

these are depot lights - they should be similar to the OEM SE tails. I don't see anything wrong with them.

DrunkieTheBear

iTrader: (17)

you know I really wonder where all this stuff gets manufactured and how they manufacture so many different lights for different cars

daesonn

they emailed me and said that the lights don't come with the rubber gasket to seal them from water leaking into the trunk, and I can't find out where to get that gasket.

DrunkieTheBear

iTrader: (17)

If I remember correctly its not a rubber gasket its some kind of goo that is already on your stock tails

daesonn

One dealership said he had some kind of tape on special order for 22$ and that was the only thing he could find in his database...

is that what i'll need?

DrunkieTheBear

iTrader: (17)

I used chaulk to be honest, it worked fine

machinehead131

iTrader: (1)

I used roof sealant or something. Worked great.

CCS2k1Max

iTrader: (2)

IMO, this doesn't warrant its own thread and search didn't turn anything up.

The last couple of months I've noticed my ABS light flickering during startup, but it turns off once the engine starts. Anyone had this experience?

NmexMAX

iTrader: (22)

Unless it stays on, I wouldn't worry.

Scottwax

iTrader: (8)

Brake fluid might be on the border of being too low.

CCS2k1Max

iTrader: (2)

Thanks, I'll double check that, but I don't think that's it. Last month or so was the last time I checked it and it was near the max.

BTW, the pedal feels fine and the ABS has been working fine in these icy side streets we have around here.

I am not worried, yet, but the flickering may be a bad sign of things to come.

NmexMAX

iTrader: (22)

The ABS light does not mean brake fluid. The BRAKE light does though.

rkreddy

I was wondering if i can get the door to close without the hard thud when its closed hard. I remember when I first got the max it used to have a nice smooth sound. There is no play with the hinges. Also what should i use to lubricate the hinges on he doors?

jbrooks870

iTrader: (4)

2 questions, first my car has the SES light on and I brought it to the mechanic and no codes came up. He cleaned an air sensor and the light went away for about a week a but reappeared and is still on. Second is it possible to mate an RB26dett engine to a 5 speed tranny and have the engine sit parallel to the front axle?

El_PrOfE

iTrader: (4)

Can anyone take on the daunting task of updating the Parts List & Web Sites for 5th gen Parts to include the 5.5th gen????? that would be amazing.

NmexMAX

iTrader: (22)

Tell me what you need and I'll tell you where to get it. Or at least try.

Scottwax

iTrader: (8)

Still used to my Mazda, one light for both. Forgot we have lights for each. Guess that is why the gauge cluster looks like a Christmas tree when I start my car.

Reket

iTrader: (1)

Does nissan have to do a TSB if its out for your car, and do I pay for it or is covered by Nissan?